manualshive.com logo in svg

Cape Dory 270, Owner'S Manual

Share
Download
Cape Dory 270 Owner'S Manual Download Page 49

 
If headsails larger than the standard jib are used, a genoa turning 
block must be installed aft of the winch to fairlead the sheet and 
decrease loads on the winch stand by sheeting directly from the track. 
 
The outboard tracks installed along the toe rail aft are for the 
sheeting of an MPS type sail. 
 

OPTIONAL SAILS 

 
The first sail that you will probably want to add to the complement of 
working sails provided with your Cape Dory is a 150% genoa.  This sail 
provides more power and speed in lighter wind conditions and is 
particularly effective going to windward.  Cape Dory has genoa and genoa 
gear packages for the CD-270.   
 
If you choose to add a spinnaker or other sails to your inventory, 
select your equipment carefully.  Your Cape Dory dealer will assist you 
in selecting suitable equipment and will make you aware of the optional 
sails and equipment that Cape Dory has available.  Due to a very low 
demand for spinnaker gear Cape Dory cannot supply any system other than 
the fittings attached to the mast.  A popular sail which acts like a 
spinnaker and a reaching genoa is a flasher.  This sail is also known as 
a MPS (Multi-Purpose Spinnaker).  It does not require a spinnaker pole 
and is easier to set and trim than a spinnaker.  Most Cape Dory 
brochures show this sail. 
 
 

XIV. STEERING SYSTEM 

 
The rudder post on all ti11er steered Cape Dory yachts extends well 
above the waterline, and occasionally when heeling or in a sloppy and 
confused chop, water will enter the cockpit through the fitting at the 
top of the rudder post.  This is not cause for concern as the volume is 
minimal and will drain out the cockpit scuppers. 
 
Maintenance of the tiller-steered Cape Dory system is simple:  keep the 
bearing at the top of the rudder post lubricated with a good waterproof 
grease.  Tilt the tiller upward and apply the grease to the top of the 
shaft and bearing.  Inspect the condition of the key.  Inspect the 
gudgeon, the heel fitting at the base of the keel where the rudder is 
connected.  There should be very little play at that point. 
 
If the tiller cap is removed from the head of the rudder post, be 
certain to re-install the tiller cap properly.  Both the rudder post and 
the tiller cap have machined keyways in them.  Be certain that the key 
is in the keyway and that the tiller cap is installed correctly. 
 
Refer to the drawing in the back of the manual for a better 
understanding of your steering system. 
 

www.capedory.org 

- 49 -

 

Summary of Contents for 270































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands