manualshive.com logo in svg

Canyon Speedmax CF SLX, Manual

Share
Download
Canyon Speedmax CF SLX Manual Download Page 2

1

EN

TABLE OF CONTENTS

2

 Welcome

4

  General notes on this manual

5

  Intended use

6  Before your first ride
6  Before every ride
6  After an accident
7

  Assembly from the BikeGuard

23

   Special features of triathlon bikes and 

time trial machines

23

 

Time trial bar end shifters

25

  Special features of carbon wheels

27

   Adjusting  the  CANYON SPEEDMAX CF 

SLX to the rider

28

 

Adjusting the saddle to the correct 
height

30

 

Fore-to-aft-position and saddle tilt

33

 

Adjusting the height of the handlebars

34

 

Adjusting extensions and armrests

38

 

Replacing extensions

39

 

Shortening the extensions

These are additional instructions for the Canyon Speedmax CF SLX. The chapters of this table 
of contents printed in black refer to your Canyon Speedmax CF SLX; there is no supplementary 
information in the Canyon bicycle manual road bike. The chapters of this table of contents 
printed in grey imperatively require that you refer to the Canyon road bicycle manual.

Important: Assembly instructions page 7. Read pages 2-6 before riding for the first time.

41

  Adjusting the trail of the fork

42

  The brake system

42

 

Checking and readjusting the  
integrated aero brakes

43

 

Front brake

47

 

Rear brake

50

 

Notes on replacing the wheels

51

 

The headset

53

  Additional accessories

59

 Warranty

61

 Guarantee

62

  Crash replacement

COMPONENTS

1

 Frame:

 

a  Top tube

 

b  Down tube

 

c  Seat tube

  d Chainstay
 

e  Rear stay

2

 Saddle

3

  Seat post

4

  Seat post clamping bolt

5

  Front derailleur

6

  Cassette sprockets

7

  Rear derailleur

8

  Rear brake

9

 Chain

10

 Chainring

11

  Crank set

12

 Pedal

13

 Stem

14

 Handlebars

15

 Armrest

16 

Extensions

17

  Shift levers

18

  Brake levers

19

 Headset

20

  Front brake

21

 Fork

22

 Drop-out

 Wheel:

23

 Quick-release

24

 Rim

25

 Spoke

26

 Tyre

27

 Hub

28

 Valve

CANYON SPEEDMAX CF SLX 

Summary of Contents for Speedmax CF SLX


































Reviews:

No comments

Brands by name

Popular brands

Load more brands