CanyCom CMX 224 Operator'S Manual Download

Page: 78 / 93

-69-

Maintenance

• Always remove battery from machine before charging. Failure to do so causes

damage to electrical components and wiring.

• Follow battery charger user's manual when charging.

Inspecting

Filling

5332M-0509-010E

Battery

UPPER

LOWER

1.  Park machine on level ground.
2.  Remove front cover.
3.  Visually inspect that battery fluid level is

between "UPPER" level and "LOWER" level
lines.

4. If fluid level is near or below "LOWER" level

line, fill.

5. Install front cover back in place.

• Instruction of removing head lamp is

indicated back of the front cover.

NOTE

UPPER LEVEL

LOWER LEVE

Filler Cap

5321M-0510-020E

1.  Remove front cover.
2.  Remove battery.
3.   Remove filler cap.
4.   Fill distilled water to "UPPER LEVEL" line.
5.  Install filler cap.
6.  Install battery.
7.  Install front cover.

Summary of Contents for CMX 224






























































































Search results

Summary of Contents for CMX 224

Reviews:

Related manuals for CMX 224

Brands by name

Popular brands

CanyCom CMX 224, Operator'S Manual

Search results

Summary of Contents for CMX 224

Reviews:

Related manuals for CMX 224

Brands by name

Popular brands