2-8-210
HOOKUP CONNECTION GUIDE
Using MEDIVATORS
®
ADVANTAGE
®
Automated Endoscope Reprocessors
ADVANTAGE HOOKUP DIAGRAM
Representative endoscope for illustrative purposes only. For exact
port locations, refer to endoscope manufacturer’s instruction guide.
Each ADVANTAGE Hookup is comprised of multiple ports and connector assemblies.
Each port is labeled with a Port ID number (circled). This same number also identifies the
corresponding Connector Assembly.
READ ALL INSTRUCTIONS PRIOR TO CONNECTION
Locate the endoscope port and follow the instructions for attaching the
corresponding Endoscope Connector. All connectors must be attached.
LOT XXXXXX ID: XXXX
P/N: X-X-XXX
Medivators Inc.
14605 28th Ave N.
Minneapolis, MN 55447
USA
Medivators BV
Sourethweg 11
6422PC Heerlen
The Netherlands
© 2015 Medivators Inc. 50098-850-EN/B
Port ID
Port Name
Connector Assembly Description
Order Number
LEAK TEST
Leak Test Connector Assembly
H28210-1
JET/AUX
Air/Water Connector Assembly
NA
BIOPSY
Biopsy Inlet Connector Assembly
H28210-3
AIR
Air Probe Connector Assembly
NA
ELEVATOR
Auxiliary Water Connector Assembly
NA
WATER
Air/Water Connector Assembly
NA
SUCTION
Suction Connector Assembly
H28210-7
EXTRA
N/A
N/A
If a Connector Assembly needs replacement, locate the port number/name and use
the corresponding order number found in the chart above. Connector Assemblies are
specific to individual hookups.
If you have any questions regarding this hookup, in the U.S., please contact
MEDIVATORS Technical Support at 1-800-444-4729. Outside the U.S., please contact
your MEDIVATORS Distributor.
CONNECTOR ASSEMBLY IDENTIFICATION CHART
Leak Test Connector
Align the slot on connector
with the pin on the scope.
Push on and turn clockwise
to engage.
Biopsy Connector
Align the biopsy connector
disc over the biopsy inlet
and push down to compress
spring and slide the frame
forward to fully engage.
Suction Connector
Align and insert the end of the connector into the
suction valve port. Firmly push the connector until
it ‘clicks’, then push the “LOCK” button until there
is another ‘click’. To remove, press the “RELEASE”
latch (make sure the “LOCK” button pops up). Tilt
the connector towards the V-notch of the scope
port while pulling the connector out.
DESIGNATED HOOKUP FOR THE FOLLOWING ENDOSCOPES*:
BF-30
BF-240AWY1
BF-P30
BF-P200
BF-1T30
BF-1T180
BF-XT40
ENF-VT
BF-40
BF-260
BF-P40
BF-P240
BF-1T30D
BF-1TQ180
BF-XT160
ENF-VT2
BF-140
BF-6C240
BF-P60
BF-P290
BF-1T40
BF-1T200
BF-F260
LTF-160
BF-160
BF-6C260
BF-P150
BF-Q180-AC
BF-1T60
BF-1T240
BF-H190
LTF-240
BF-180
BF-MP160
BF-P160
BF-Q190
BF-1T130
BF-1T260
BF-XP190
MAF-TM
BF-200
BF-MP160F
BF-P180
BF-TE2
BF-1T150
BF-Q180
BF-1TH190
BF-240
BF-MP60
BF-P190
BF-XP160
BF-1T160
BF-XT30
BF-P260F
* This list of corresponding endoscope models is subject to change without notice. For a full list, please go to:
www.medivators.com/hookuplookup
