background image

Batteries and Using the AC Power/Charger 

Attaching and Removing the Battery Pack 

1.  To attach the battery pack to the camcorder, 

press the battery pack softly into the battery 
compartment      and slide it up until it clicks 
into place. 

 
 
 
 
 

2.  To remove the battery pack:  

a.  Hold onto the battery pack and slide the 

Battery Release Switch

      in the 

direction of the arrow. 

b.  Slide the battery pack down and remove it 

from the battery compartment      . 

 
 
 
 
Using the AC Power Adapter to Operate the Camcorder and Charge the Battery 

1.  Make sure the camcorder power is 

turned off

 

before 

connecting or disconnecting the AC 

power adapter. 

2.  If you are attempting to charge the camcorder 

battery while it is on the camera using the AC 
power supply, the battery will only be charged 
when the camcorder is 

turned off

3.  When fully charged, the supplied battery 

should provide approximately 130 minutes of 
recording time. 

 

Canon VIXIA HF200 Quick Start Guide 

 

Overview 

This camcorder should not be used for taking still photographs.  If you wish to take 
digital still photos, our department has digital still cameras for loan that will yield much 
higher quality pictures.  

 

Please use this unit in the Video Only Mode which is the movie 
camera icon located in the center position on the camera mode 
dial. 

 

Important Operational Notes:

 

Handling Precautions

 

1.  Do not carry the camcorder by the LCD panel. 
2.  Do not leave the camcorder in places of high heat or humidity. 
3. 

Do not use camcorder near strong magnetic fields such as TV’s, or plasma 
screens. 

4.  Do not subject the camcorder to shock or vibration. 
5.  When mounting the camcorder to a tripod, remove the tripod plate from the tripod 

and attach it to the camera first then attach the camcorder and plate to the tripod. 

6.  Do not point or leave the camcorder pointed at bright light sources. 
7.  Do not attempt to clean the LCD screen. 

 

SDHC Memory Cards Needed for Recording Video 

1.  Media Services does not supply the SDHC memory cards that you will need to 

record your video.   

2.  The cards must have a speed rating of at least 

class 4 or 6

.  These can be 

purchased at the university’s bookstore or at most locations that sell consumer 
electronics or office supplies. 

3. 

Only purchase SDHC memory cards from the following manufacturers: 

SanDisk, Panasonic or Toshiba

.

 

Use of other manufacturer’s memory cards 

may result in the loss of the recorded video.

 

4.  A 4GB SD or SDHC card will yield approximately 1 hour and 10 minutes of 

recording time.  An 8 GB SD or SDHC card will yield approximately 2 hours and 
20 minutes of recording time. 

5.  CAUTION: DO NOT USE Wi-Fi MEMORY CARDS. 

Summary of Contents for VIXIA HF200







Reviews: