background image

 

GETTING STARTED

 

 

CHARGING 

 

 

 

 

 

Charging Status LED   

 

 

Charging :  Red 

 

 

 

Full :  Green 

 

 

 

 

 

 

The device has a built-in battery. Please fully charge the device via the USB cable provided before using. 

1.

 

Insert the smaller end of the supplied USB cable into the device and other end into a chargeable USB 
adapter. 

2.

 

 The charging LED light, at the bottom of the device, will turn red to indicate charging. 

3.

 

Once fully charged, the charging LED will turn green. 
- Operating time may vary depending on the battery status, operational status and environment 
conditions. 

 
 

INSERTING SD CARD 

 

  An external MicroSD card (up to 256 GB) is needed for saving captured photos. 

Only FAT16, FAT32 and exFAT format are supported. 

 
PREPARING A MEMORY CARD 
Use the following memory cards (sold separately) 

 

MicroSD memory cards *1 

 

MicroSDHC memory cards *1*2 

 

MicroSDXC memory cards *1*2 

 
*1 Cards conforming to SD standards. However, not all memory cards have been verified to work with the camera. 
*2 UHS-I memory cards are also supported. 
 
INSTALL AND REMOVE THE MicroSD CARD 

 

Insert the MicroSD card into the slot at the bottom of the device. You will feel a slight click when the card 
is fully inserted. 

 

Push on the top of the card to release it. Gently pull to fully remove the card from the device. 

 

If there is an error on ready / writing to the MicroSD card, the MicroSD Error LED Indication will be 
displayed. 

 

Connect the device to a computer by USB cable. Double-click the external drive image when it appears on 
the computer to view and save the photos. 

 

 

 

 

Summary of Contents for PP2002










Reviews: