manualshive.com logo in svg

Canon PIXMA MG5600 Series, Online Manual

Share
Download
Canon PIXMA MG5600 Series Online Manual Download Page 723

The Machine Stopped Working Suddenly

Cannot Communicate with the Machine After the Network Settings Are Changed

Cannot Communicate with the Machine over the Wireless LAN

Cannot Communicate with the Machine Using the Access Point Mode

Cannot Print or Scan from a Computer Connected to the Network

Cannot Communicate with the Machine After the Network Settings Are
Changed

It may take a while for the computer to obtain the IP address, or you may need to restart your computer.

Search for the machine again after confirming a valid IP address is assigned to the computer.

Cannot Communicate with the Machine over the Wireless LAN

Check1

 Make sure that the machine is turned on.

Check2

 Make sure that the network settings in the machine are identical with those of

the access point.

Refer to the instruction manual provided with the access point or contact its manufacturer to check the access
point settings, and then modify the machine settings.

How to Set an Encryption Key

Check3

 Make sure that the machine is not placed far away from the access point.

The access point is located indoors within the effective range for wireless communication. Locate the machine
within 164 ft. / 50 m from the access point.

Check4

 Make sure that there is no obstruction.

Wireless communication between different rooms or floors is generally poor. Adjust the location of the devices.

Check5

 Make sure that there is no source of radio wave interference in your vicinity.

If a device (e.g. microwave oven) using the same frequency bandwidth as the wireless station is placed
nearby, the device may cause interference. Place the wireless station as far away from the interference source
as possible.

Check6

 Make sure that the network settings of the computer are correct.

For the procedures to connect a network device to the computer and set them up, refer to the instruction
manual of your network device or contact its manufacturer.

Check7

 Make sure that the radio status is good and adjust the installation positions

while monitoring the radio status with IJ Network Tool.

Monitoring Wireless Network Status

Check8

 Make sure that a valid wireless channel is used.

723

Summary of Contents for PIXMA MG5600 Series















































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands