Canon MX720 Series Online Manual Download Page 192

Page: 192 / 248

Canon IJ Network Tool Screen

This section describes the items and menus displayed on the

Canon IJ Network Tool

screen.

Items on the

Canon IJ Network Tool

Screen

Canon IJ Network Tool

Menus

Items on the Canon IJ Network Tool Screen

The following item is displayed on the

Canon IJ Network Tool

screen.

Printers:

The printer name, status, printer model name, and port name are displayed.
A check mark next to the printer in the

Name

list indicates it is set as the default printer.

Configuration changes are applied to the selected printer.

Update

Performs printer detection again. Click this button if the target printer is not displayed.

Important

To change the printer's network settings using IJ Network Tool, it must be connected via a

LAN.

No Driver

is displayed for the name, associate the port with the printer.

When the Printer Driver Is Not Associated with a Port

Not Found

is displayed for the status, check the followings:

The access point is turned on.
When using wired LAN, the LAN cable is connected properly.

If the printer on a network is not detected, make sure that the printer is turned on, then click

Update

. It may take several minutes to detect printers. If the printer is not yet detected,

connect the machine and the computer with a USB cable, then click

Update

If the printer is being used from another computer, a screen is displayed informing you of

this condition.

Note

This item has the same function as

Refresh

in the

View

menu.

Configuration...

Click to configure settings of the selected printer.

Configuration Screen

Note

You cannot configure a printer that has the status

Not Found

Summary of Contents for MX720 Series

























































































































































































































































Search results

Summary of Contents for MX720 Series

Reviews:

Canon MX720 Series, Online Manual, Page: 192 / 248

Search results

Summary of Contents for MX720 Series

Reviews: