ENG-2
0615Ni
©
CANON INC. 2015
❺
❻
4. Manual Focus
When the camera’s focus mode is set to [MF], focus manually by
turning the focusing ring. (fig.
❺
)
Quickly rotating the focusing ring may result in delayed focus.
•
Focus mode is set using the camera. Please refer to the
camera’s instructions.
•
After autofocusing in [AF+MF] mode, focus manually by
pressing the shutter button halfway and turning the focusing
ring (full-time manual focusing).
5. Image Stabilizer
This lens is equipped with an Image Stabilizer. This function
corrects camera shake, allowing users to capture sharp images.
Also, the Image Stabilizer automatically provides optimal image
stabilization depending on shooting conditions (such as shooting
still subjects and following shots). Please set the Image Stabilizer
ON or OFF using the camera settings. See your camera’s
instructions for details.
•
The Image Stabilizer cannot compensate for a blurred shot
caused by a subject that moved.
•
The Image Stabilizer may not be fully effective if you shoot
from a violently shaking vehicle or other transportation.
•
The Image Stabilizer consumes more power than normal
shooting, resulting in fewer shots and a shorter movie
shooting time.
•
When shooting a still subject, it compensates for camera
shake in all directions.
•
It compensates for vertical camera shake during following
shots in a horizontal direction, and compensates for
horizontal camera shake during following shots in a vertical
direction.
•
When you use a tripod, the Image Stabilizer should be
turned off to save battery power.
•
Even with a monopod, the Image Stabilizer will be as
effective as during hand-held shooting.
However, depending on the shooting environment, the
Image Stabilizer effect may be less effective.
6. Hood (sold separately)
The EW-53 hood cuts out unwanted light and protects the front of
the lens from rain, snow, and dust.
To attach the hood, align the hood’s attachment position mark with
the red dot on the front of the lens, then turn the hood as shown
by the arrow until the lens’ red dot is aligned with the hood’s stop
position mark. (fig.
❻
)
The hood can be reverse-mounted on the lens for storage.
•
If the hood is not attached properly, vignetting (darkening of
the perimeter of the picture) may occur.
•
When attaching or detaching the hood, grasp the base of
the hood to turn it. To prevent deformation, do not grasp the
rim of the hood to turn it.
7. Filters (sold separately)
You can attach filters (which are 49 mm in diameter) to the filter
mounting thread on the front of the lens.
Only one filter may be attached.
Specifications
Focal Length/Aperture
15-45mm f/3.5-6.3
Lens Construction
9 groups, 10 elements
Minimum Aperture
f/22-40*
Angle of View
Diagonal: 84°30'-33°40'
Vertical: 53°30'-19°05'
Horizontal: 74°10'-28°20'
Min. Focusing Distance
0.25 m/0.82 ft.
Max. Magnification
0.25x (at 45 mm)
Field of View
Approx. 185x283-61x92 mm/
7.28x11.14-2.40x3.62 inch
(at 0.25 m/0.82 ft.)
Filter Diameter
49 mm
Max. Diameter and Length
60.9x44.5 mm/2.40x1.76 inch
(When the lens is retracted)
Weight
Approx. 130 g/4.6 oz
Hood
EW-53 (Sold Separately)
Lens Cap
E-49
Dust Cap
Lens Dust Cap EB
Case
LP811 (Sold Separately)
* Applies to 1/3-stop increments. With 1/2-stop increments, it will
be f/22-38.
• Equivalent to 24-72 mm in the 35mm film format.
• The lens length is measured from the mount surface to the front
end of the lens. Add approx. 20 mm when including the lens cap
and dust cap.
• The size and weight listed are for the lens only, except as
indicated.
• Neither extenders nor close-up lenses can be used with the
lens.
• Aperture settings are specified on the camera. The camera
automatically compensates for variations in the aperture setting
when the camera is zoomed in or out.
• All data listed is measured according to Canon standards.
• Product specifications and appearance are subject to change
without notice.
