Canon iP4500 - PIXMA Color Inkjet Printer Simplified Service Manual Download Page 7

 

 

 

Inner cover open before start 

of printing on paper. [1841] 

(At CD-R is not supported.)   

Close the inner cover, and press the 

Resume/Cancel button. (At CD-R is not 

supported.) 

 

Inner cover open during   

printing on paper. [1846] 

(At CD-R is not supported.) 

Close the inner cover, and press the 

Resume/Cancel button. (At CD-R is not 

supported.) 

 

Inner cover open before start 

of printing on paper (print 

continuable). [1856] 

 

Close the inner cover, and press the 

Resume/Cancel button to clear the error. 

The paper being printed at error 

occurrence will be ejected without printing 

the remaining data for the ejected paper, 

then printing will resume from the next 

page. 

 

Inner cover closed before 

start of CD / DVD printing 

(print continuable). [1850] 

Open the inner cover which functions as 

the CD / DVD tray feeder, set the CD / 

DVD tray in the feeder, and press the 

Resume/Cancel button. 

 

Inner cover open before start 

of CD / DVD printing (print 

continuable). [1851] 

Close the inner cover, and press the 

Resume/Cancel button. 

 

6 times 

Inner cover closed during 

CD / DVD printing (print 

NOT continuable). [1855] 

Open the inner cover, and press the 

Resume/Cancel button to clear the error. 

The CD or DVD being printed at error 

occurrence will be ejected without printing 

the remaining data for the ejected CD or 

DVD, then the next print job will be 

performed. 

 

Multiple ink tanks of the 

same color installed. [1681] 

Replace the wrong ink tank(s) with the 

correct one(s). 

Install the ink cartridge(s), 

and close the access cover. 

7 times 

Ink tank in a wrong position. 

[1680] 

Install the ink tank(s) in the correct position.   

8 times 

Warning:   The ink absorber 

becomes almost full. [1700] 

Press the Resume/Cancel button. 

The service call error, 

indicating the ink absorber is 

full, is likely to occur soon. 

9 times 

The connected digital 

camera or digital video 

camera does not support 

Camera Direct 

Printing. [2001] 

Remove the cable between the camera 

and the printer. 

 

10 times 

Automatic duplex printing 

cannot be performed. [1310] 

Press the Resume/Cancel button to eject 

the paper being used at error occurrence. 

Printing will resume from on the front side 

of the next page. 

Data which was to be printed 

on the back side of paper at 

error occurrence is skipped 

(not printed). 

 

Summary of Contents for iP4500 - PIXMA Color Inkjet Printer























































Reviews: