manualshive.com logo in svg

Canon imageCLASS MF6500 Series, Service Manual

Share
Download
Canon imageCLASS MF6500 Series Service Manual Download Page 171

Chapter 13

13-3

13.3.3 Service Error Code

13.3.3.1 Service Error Code

0012-5782

LaserBase MF6530 /  / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL /  / LaserBase MF6580PL

T-13-5

#0018

[Tx/Rx] 

auto call initiation has failed.

#0037 

[Rx]

image memory overflow at time of reception has occurred.

#0059 

[Tx]

The number you dial and connected number (CSI) does not match.

#0995/0099 [Tx/Rx] 

a memory communication reservation has been cancelled.

No. Tx/Rx

Description

##0100 

[Tx]

at time of transmission, the procedural signal has been transmitted more than specified.

##0101 

[Tx/Rx]

the modem speed does not match that of the other party.

##0102 

[Tx] 

at time of transmission, fall-back cannot be used.

##0103 

[Rx]

at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).

##0104 

[Tx]

at time of transmission, RTN or PIN is received.

##0106 

[Rx]

at time of reception, the procedural signal is received for 6 sec while in wait for the signal.

##0107 

[Rx]

at time of reception, the transmitting party cannot use fall-back.

##0109 

[Tx]

at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been 
sent more than specified.

##0111 

[Tx/Rx]

memory error has occurred.

##0114 

[Rx]

at time of reception, RTN is transmitted.

##0200 

[Rx]

at time of reception, no image carrier is detected for 5 sec.

##0201 

[Tx/Rx]

DCN is received outside the normal parity procedure.

##0220 

[Tx/Rx]

system error (main program out of control) has occurred.

##0232 

[Tx]

encoding error has occurred.

##0237 

[Rx]

decoding error has occurred.

##0261 

[Tx/Rx]

system error has occurred.

##0280 

[Tx]

at time of transmission, the procedural signal has been transmitted more than specified.

##0281 

[Tx]

at time of transmission, the procedural signal has been transmitted more than specified.

##0282 

[Tx]

at time of transmission, the procedural signal has been transmitted more than specified.

##0283

[Tx]

at time of transmission, the procedural signal has been transmitted more than specified.

##0284 

[Tx]

at time of transmission, DCN is received after transmission of TCF.

##0285 

[Tx]

at time of transmission, DCN is received after transmission of EOP.

##0286 

[Tx]

at time of transmission, DCN is received after transmission of EOM.

##0287 

[Tx]

at time of transmission DCN is received after transmission of MPS.

##0288

[Tx] 

after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##0289 

[Tx]

after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##0290

[Tx]

after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##0670 

[Tx] 

at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is 
expected to be transmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-
out.

##0671

[Rx]

at time of V.8 arrival, procedure fails to move to phase 2 after detection     of CM signal from caller, causing T1 time-out 
and releasing line

##0672 

[Tx]

at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release 
the line and suffer T1 timeout.

##0673 

[Rx]

at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release 
the line and suffer T1 timeout.

##0674

[Tx]

at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, 
causing the machine to release the line and suffer T1 timeout.

##0675 

[Rx]

at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing 
the machine to release the line and suffer T1 timeout.

##0750 

[Tx] 

at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural 
signal to be transmitted more than specified.

##0752 

[Tx]

at time of ECM transmission, DCN is received after transmission of PPS-NULL.

##0753 

[Tx]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-
NULL, or T5 time-out (60 sec) has occurred.

##0754 

[Tx]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-
NULL.

##0755 

[Tx]

at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal 
to be transmitted more than specified.

##0757 

[Tx]

at time of ECM transmission, DCN is received after retransmission of PPS-MPS.

##0758 

[Tx]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, 
or T5 time-out (60 sec) has occurred.

##0759 

[Tx] 

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.

##0760 

[Tx]

at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural 
signal to be transmitted more than specified.

##0762 

[Tx]

at time of ECM transmission, DCN is received after transmission of PPS-EOM.

##0763 

[Tx]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, 
or T5 time-out (60 sec) has occurred.

No.

Tx/Rx

Description

Download Free Service Manual And Resetter Printer at http://printer1.blogspot.com

Summary of Contents for imageCLASS MF6500 Series





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands