manualshive.com logo in svg

Canon FAX L1000, Service Manual

The Canon FAX L1000 is a high-performance fax machine suited for efficient communication needs. Unlock its full potential with the comprehensive Service Manual, available for free download at manualshive.com. This manual ensures smooth operations and troubleshooting, enabling users to maximize the product's capabilities.

Share
Download
background image

3-92

FAX-L1000 Chapter 3: Technical Reference

NOTE

The characteristics of Progressive Bi-level Image Compression are explained
below as a reference. First of all, after the original image has been read in at
high resolution, it is converted to low resolution, and this low resolution
image data proceeds to be encoded (compressed). On the receiving end, the
overall original image can be quickly recognized by the steps in which this
low resolution image compression data is received.
Next, to improve the quality of the low resolution image already sent, only
information needed to improve the resolution is forwarded. The previous low
resolution image is decoded on the receiving side with this information, and
following this, the high resolution image is displayed on top of the previous
low resolution image.
It is easy to quickly recognize the original image in the process of displaying
the image from low resolution to high resolution in order by using this
method, with a CRT display for example. Also, according to the situation, it
is possible to interrupt the image transfer at the point where the original
image is recognized to some degree by the receiving side.
This method requires a page buffer memory for the low resolution image
because the low resolution images are used for the purpose of high resolution
image encoding.

3.2.2 Single Progression Sequential Bi-level Image Compression Method

The Single Progression Sequential Bi-level Image Compression Method used in this fax is
explained below.
The Progressive Bi-level Image Compression Method uses multiple resolution layers on a
single page (multi-level layers, low resolution layers~high resolution layers) to perform
encoding/decoding. In the Single Progression Sequential Bi-level Image Compression
Method, encoding is done in units of horizontal bands (a number of lines) called stripes, and
is performed from left to right, top to bottom (this condition is called sequential), and in one
resolution layer (single layer).

NOTE

In this method, the encoding is done in stripe units, so it is completed with a
buffer memory much smaller than a page buffer memory.

The methods by which encoding takes place and by which image data is constructed after
encoding are explained below.

Summary of Contents for FAX L1000



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for FAX L1000

UNIS TOYBOX Operation Manual preview
TOYBOX
Brand: UNIS Pages: 19
Tornado 99732 Operation & Maintenance Manual preview
99732
Brand: Tornado Pages: 23
Nancy’s Knit Knacks Lazy Kate Assembly Instructions And User'S Manual preview
Lazy Kate
Brand: Nancy’s Knit Knacks Pages: 2
Garudan GPS/F-1006 Series User Programming Manual preview
GPS/F-1006 Series
Brand: Garudan Pages: 114
Powermax Tech AHE58-55 Instruction Manual preview
AHE58-55
Brand: Powermax Tech Pages: 16
JUKI MO-2800 Instruction Manual preview
MO-2800
Brand: JUKI Pages: 40
Happy HCG Series Instruction Book preview
HCG Series
Brand: Happy Pages: 98
JUKI MH-486-5 Instruction Manual preview
MH-486-5
Brand: JUKI Pages: 32
JUKI DDL-8700 Specifications preview
DDL-8700
Brand: JUKI Pages: 2
Mi-T-M AW-7020-8006 Manual preview
AW-7020-8006
Brand: Mi-T-M Pages: 2
Stern Pinball Heavy Metal Service And Operation Manual preview
Heavy Metal
Brand: Stern Pinball Pages: 44
Yamato FD-62DRY Instruction Manual preview
FD-62DRY
Brand: Yamato Pages: 54
Sharp FO-A660 Operation Manual preview
FO-A660
Brand: Sharp Pages: 103
Sharp FO-455 Operation Manual preview
FO-455
Brand: Sharp Pages: 98
Sharp FO-CC500 Operation Manual preview
FO-CC500
Brand: Sharp Pages: 139
Sharp FO-B1600 Service Manual preview
FO-B1600
Brand: Sharp Pages: 138
Sharp FO-D60 Operation Manual preview
FO-D60
Brand: Sharp Pages: 147
Sharp FO-A650 Operation Manual preview
FO-A650
Brand: Sharp Pages: 186

Brands by name

Popular brands

Load more brands