background image

 

The information contained herein is presented only as a guide for the application of our products. No responsibility is assumed by Canon Electron Tubes 

& Devices Co., Ltd. (CETD) for any infringements of patents or other rights of the third parties which may result from its use. 
No license is granted by implication or otherwise under any patent or patent rights of CETD or others. 

The information contained herein may be changed without prior notice. It is therefore, advisable to contact to CETD before processing with the design of 

equipment incorporating this product. 

 

CANON ELECTRON TUBES 
      & DEVICES CO., LTD. 

Engineering Information

 

EI

 

  No.  EE-E3730A    2020-08-04   

 

 

 

 

 

 

 

High Power Pulse Klystron 

E3730A 

Operating Instructions

 

 
 
 
 
 
 
 
 
 
 

* We are appreciating your purchase of our klystron product. 

* Please read carefully this instruction manual before operating the klystron tube 

to use it properly. 

* Please keep this instruction manual carefully not to lose.

 

 

 
 
 
 
 
 

Aug, 2020 

 

CANON ELECTRON TUBES & DEVICES CO., LTD.

 

 

 

 

Summary of Contents for E3730A


























Reviews: