Canon CR-X300 User Manual Download Page 100

Page: 100 / 114

100

For the latest information on this product (firmware and software, user manuals, operating environment, etc.), refer to the

Canon website.

CR-X300 Main Unit



Camera

Specifications

Image Sensor

Type 1/2.3 (1/2.3 in.) single-plate CMOS sensor
Total pixels: approx. 21.14 megapixels
Effective pixels: approx. 8.29 megapixels (3840 x 2160)

Lens

f=3.67 – 73.4 mm, F/1.8 – 2.8, 20x optical zoom
35mm equivalent focal length: [4K UHD] approx. 29.3 (W) – 601 mm (T)

[Full HD] approx. 30.5 (W) – 627 mm (T)

8-bladed circular aperture
12 elements in 10 groups (including 2 aspheric elements)

Digital Zoom

20x

Minimum Focusing Distance

1 cm (0.39 in.) at maximum wide angle, 60 cm (2.0 ft.) throughout the zoom
range (from the lens protector)

Angle of View

[4K UHD]
Horizontal: 65.6° (W) – 3.6° (T)
Vertical: 39.8° (W) – 2.0° (T)
[Full HD]
Horizontal: 63.5° (W) – 3.4° (T)
Vertical: 38.4° (W) – 1.9° (T)

Shutter Speed

1/6 – 1/2000 sec. (specific values depend on the frame frequency)

Focus

Focus mode: Manual, Continuous AF, Face Detection AF, Tracking
AF type: Hybrid AF, Contrast AF

Shooting Mode

F.Auto, P, Tv, Av, M

Scene Mode

Portrait, Sports, Low light, Spotlight

Custom Picture

Gamma

Normal1, Normal3

Color Space

BT.709, BT.2020

Color Matrix

Neutral, Video

ND Filter

ND filter: 1/8 at maximum
Enhanced ND filter: 1/32

IR Mode

Electrically switchable

Image Stabilizer

Optical-shift (Standard IS, Powered IS)

White Balance

AUTO (AWB), Set A, Set B, preset settings (daylight: approx. 5600 K*, tungsten
lamp: approx. 3200 K*), color temperature setting (2000 K – 15000 K), Manual
* Color temperatures are given for reference purposes only.

Gain

0.0 – 36.0 dB

Min. Subject Illumination

Approx. 3.0 lux (shutter speed 1/60 sec., frame frequency 59.94 Hz (P (Program
AE) shooting mode), auto slow shutter "Off")

Video Flip

Supports upright/ceiling installation, flip function ("Auto Flip" enabled/disabled)

Built-in Microphone

Waterproof microphone

Summary of Contents for CR-X300



















































































































Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands

Canon CR-X300, User Manual

Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands