Home
/
Canon
/
Colorado 1630
/
Operation Manual

Canon Colorado 1630, Operation Manual

Share

Page: 170 / 388

Canon Colorado 1630 Operation Manual Download Page 170

Action

Procedure

Clean the platen.

Clean the platen on page 191

Clean the platen

Clean the buffer plate.

Clean the buffer plate on page 194

Clean the buffer plate

The printer performs a purge and
wipe to clean the nozzles.

Clean the nozzles

You can select the option [Advanced automatic nozzle
optimization].
A test pattern will be printed that will be checked by the
system to obtain the best print quality.
Video:

Automatic nozzle optimization

Incident-based (quality problems, paper jam, crash)

Periodic maintenance

Periodic maintenance is a variety of mandatory maintenance actions that have to be performed
by the operator. Periodic maintenance has to be done when the operator panel gives a warning.
This is al least once a month, and depending on the ink usage, between 7 and 30 days.

IMPORTANT

You must perform all periodic maintenance indicated on the operator panel, to guarantee the

print quality.

Action

Procedure

Clean the maintenance station, in-
cluding the wiper and clean wall.

Clean the maintenance station, wiper and clean wall on
page 178

Clean the maintenance station

Clean the matrix plate area.

Clean the matrix plate area on page 182

Clean the matrix plate

Clean the mirrors

Clean the mirrors on page 247

Clean the mirrors

Clean the M&C scanner.

Clean the M&C scanner on page 188

Clean the M&C scanner

Clean the platen.

Clean the platen on page 191

Clean the platen

Clean the buffer plate.

Clean the buffer plate on page 194

Clean the buffer plate

Vacuum the chiller and check the flu-
id level

Vacuum the chiller and check the fluid level (first design)
on page 231

Vacuum the chiller

Clean the ink unit

Clean the ink unit on page 251

Clean the ink unit

4

Guidelines to maintain the print quality

170

Chapter 6 - Maintain the system

«
...
168
169
170
171
172
...
»

Summary of Contents for Colorado 1630





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands