background image

 

1-7

 

 

1-7 

Note 

Put following sentences outside of the host device if the FCC ID on the module cannot be seen from exterior. 

“Contains Transmitter Module FCC ID: AZDFM48944” or “Contains FCC ID: AZDFM48944” 

“Contains Transmitter Module IC: 498D-FM48944” or “Contains IC: 498D-FM48944” 

 

User’s manual of the host device should contain sentences listed below. 

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause

 

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. 
 
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure 
Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the 
radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).     
 
FCC WARNING 
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 
 
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, 
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
—Consult the dealer or an experienced radio/TV technician for help.   
 
This equipment complies with the Canadian ICES-003 Class B limits. 
 

Summary of Contents for Board-C1








Reviews: