background image

CANNON LIMITED WARRANTy

Johnson Outdoors Marine Electronics, Inc. (“JOME”) extends the following limited warranty to the original retail purchaser only.  Warranty coverage is not 
transferable.

CANNON® LIMITED LIFETIME WARRANTy

JOME warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the 
following warranty periods, JOME will, at its option, either repair or replace same without charge (but no cash refunds will be made): 

The boom, motor (if applicable), and reels, plus all plastic parts, including but not limited to frames and bases, will be free from defects in materials and 
workmanship, subject to normal wear and tear, for the original purchaser’s lifetime. 

LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND CERTAIN DAMAGES

THERE  ARE  NO  EXPRESS  WARRANTIES  OTHER  THAN  THESE  LIMITED  WARRANTIES.  JOME  DISCLAIMS  LIABILITY  FOR  INCIDENTAL  AND 
CONSEQUENTIAL  DAMAGES,  AND  IN  NO  EVENT  SHALL  ANY  IMPLIED  WARRANTIES  (EXCEPT  ON  THE  BOOM,  MOTOR,  REELS,  AND  ALL  PLASTIC 
PARTS), INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXTEND BEYOND ONE YEAR FROM 
THE DATE OF PURCHASE (AND IN THE CASE OF THE SWIVEL LOCK PIN, WEIGHTS, AND WIRE CABLE, JOME DISCLAIMS ALL IMPLIED WARRANTIES). 
THIS  WRITING  CONSTITUTES  THE  ENTIRE  AGREEMENT  OF  THE  PARTIES  WITH  RESPECT  TO  THE  SUBJECT  MATTER  HEREOF;  NO  WAIVER  OR 
AMENDMENT SHALL BE VALID UNLESS IN WRITING SIGNED BY JOME.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of consequential damages, so the above limitation 
or exclusion may not apply to you. This warranty gives you specifi  c legal rights, and you may also have other rights that vary from state to state. 

CANNON® SERVICE POLICy

AFTER THE APPLICAbLE WARRANTy PERIOD 

After the applicable warranty period, or, if one of the above exclusions applies, Cannon® products will be repaired for a charge of parts plus labor. 

TO ENFORCE WARRANTy OR TO ObTAIN REPAIRS AFTER WARRANTy 

To obtain warranty service in the U.S., the downrigger believed to be defective and the proof of original purchase (including the date of purchase) must be 
presented to a Cannon® Authorized Service Center or to Cannon®’s factory service center in Mankato, MN. Except as noted below, any charges incurred for 
service calls, transportation or shipping/freight to/from the Cannon® Authorized Service Center or Cannon®’s factory, labor to haul out, remove, re-install 
or re-rig products for warranty service, or any similar items are the sole and exclusive responsibility of the purchaser. If the necessary repairs are covered by 
the warranty, we will pay the return shipping charges to any destination within the United States. Downriggers purchased outside of the U.S. (or parts of 
such downriggers) must be returned prepaid with proof of purchase (including the date of purchase and serial number) to any Authorized Cannon® Service 
Center in the country of purchase. 

NOTE: 

Do not return your Cannon® downrigger or parts to your retailer. Your retailer is not authorized to repair or replace them. 

Major parts, such as the motor and main frame, must be returned to JOME in Mankato, Minnesota, or a Cannon® Authorized Service Center, for repair or 
replacement. To reduce shipping costs, we suggest removal of loose parts such as the boom and rod holders. Small parts that can be easily removed such as 
the handle and/or the counter, may be removed from the downrigger and returned for repair or replacement. 

Retain your sales receipt. 

Proof of purchase 

must accompany product when returned.

LIMITED WARRANTY

Summary of Contents for DIGI-TROLL 10




































Reviews: