background image

Cannon Fitzroy / Canterbury Inbuilt | 11

fitzroy inbuilt fasCia reMoVal

Canterbury inbuilt fasCia reMoVal

1.   remove the wire mesh grille by gently lifting it 

upwards and then outwards. Similarly remove a fitted 
glass kit by also gently lifting it upwards and then 
outwards.

2.   remove 4 M5 screws fixing the fascia assembly to the 

heater body. bring the bottom of the fascia towards 
you gently to partly disengage it from the body of the 
heater. after it has been disengaged gently lift it up 
vertically to completely disengage it from the body of 
the heater. refer 

FIG 10

 & 

FIG11

.

 Inner Glass Removal For Both FITZIB & CANTIB 

to remove the inner glass loosen off all the clamp screws 
and completely remove the one vertical side.  
try not to touch the front surface of the glass. to avoid 
finger marks use suitable cloth. remove the glass by  
sliding the glass sideways out of the clamp and then  
lifting out from the bottom. Place the glass in a safe  
position for refit later.

fig 10

fig 15

fig 12

fig 16

fig 13

fig 17

fig 14

fig 11

to fully remove the 
fascia, unclip the switch 
cable from the cable 
connector on the PCb 
and unclip the cable from 
the clipping points on  
the rear of the fascia.

1.   to remove the inner fascia assembly undo two screws 

in the upper flange as indicated in 

FIG 12

. remove 

the inner fascia assembly by holding the glass 
surround and firmly pull it towards you. refer 

FIG 13

.

2.   remove the lower front cover by unscrewing two M5 

screws through the air intake slots. refer 

FIG 14

 unit 

is fitted with electronic swtiches ensure that the cable 
cannot be trapped when the heater is installed.

3.   to remove the front heater surround undo two screws 

(one either side) from the bottom flange of  
the front panel as indicated in 

FIG 15

.

4.   remove the surround by pulling the lower section 

towards you gently to partly disengage it from the 
body of the heater, then gently lift it vertically to 
completely disengage it. refer 

FIG 16

.

5.   to fully remove the fascia, unclip the switch cable  

from the PCb connector and unclip the cable from  
the clipping points. the cable is routed through a 
plastic grommet which will have to be removed from 
the base plate. refer 

FIG 17

.

grommet

Summary of Contents for CANTERBURY





















Reviews: