27
26
Alarm mute for the PROGRAMME
END
The alarm
for the programme end
may
be muted as follows:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1.
Hold down the
"PROGRAMME
SELECTION"
button and at the same
time
switch on
the dishwasher by
pressing the
"ON/OFF"
button (a brief
audible signal will sound).
2.
Keep the
"PROGRAMME SELECTION"
button pressed for at least
15
seconds
(during this time, 2 audible signals will
sound).
3.
Release the button when the
second
audible signal sounds (3
"PROGRAMME
SELECTION"
indicator lights will come
on).
4.
Press the same button again: the 3
indicator lights (which indicate that the
alarm is activated) will start flashing (to
indicate that the alarm is off).
5.
Turn off the dishwasher by pressing the
"ON/OFF"
button to confirm the new
setting.
To turn the alarm on again, follow the same
procedure.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the
"COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the
"ON/OFF"
button.
After checking to make sure the water
inlet hose tap is open, that the drain
hose is not bent and that the siphon or
filters are not clogged, set the selected
programme again.
If the anomaly persists, contact Customer
Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
IMPORTANT
The dishwasher has two very practical
functions:
- the "recommended" programme
(which is set in the factory and is
ideal for full-load daily use) for quick
and accurate selection;
- the memory function which saves
the last programme used, so that if
you regularly use the same washing
cycle, you do not have to re-set the
programme every time, thereby
saving time and effort.
Programme settings
■
Open the door and place the dirty dishes
inside the appliance.
■
Press the
"ON/OFF"
button .
The indicator light for the
"recommended"
programme or the indicator light for the
last programme used will flash.
■
Choose a programme by pressing the
"PROGRAMME SELECTION"
button
(PR.)
. The selected programme indicator
light will come on.
When the
"COLD RINSE"
programme is
selected, 2 indicator lights will come on.
■
Close the door (after an audible signal
has sounded, the programme will start
automatically).
WITHIN one minute of the programme
commencing, another programme
can be selected, simply by pressing
the "PROGRAMME SELECTION"
button.
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically. Close the door,
without
pressing any buttons
. The cycle will start
from where it left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running program:
■
Hold the
"PROGRAMME SELECTION"
button down for at least
5
seconds.
The programme indicator lights will flash
and some audible signals will sound.
■
The running programme will be cancelled
and the indicator light for the
“recommended”
programme will start
to flash.
■
At this point a new programme can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme end
A 5 seconds alarm will sound (if not muted)
3 times at 30 seconds intervals to signal
that the programme has ended.
The selected programme indicator light (2
indicator lights for the
"COLD RINSE"
programme) will start to flash.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF"
button or dishes can be loaded
for new cycle.
