background image

DEPENDING ON THE MODEL, ALL LINES MAY NOT FUNCTION 

UNLESS BASIC PROGRAMMING IS COMPLETED.  

IF ALL LINES DO NOT WORK, YOU CAN ENABLE THEM WITH 

BASIC PROGRAMMING - IT'S EASY!

Basic Programming (do not do this unless you have to):

Before you start programming, ensure you have connected your first phone to 
the port marked 11, this is referred to as Extension-11 or Phone-11 and is the 
first of 6 or 8 phones you can have on your Mini-PABX.

N.B. If at any time you feel you want to start again, you can reset to Factory 
Defaults by the command 

0000 #

 (first Enter Program Mode – see below)

Enter Programming Mode:

Pick up Extension-11 (Port-11)
Key-in (Type) 

* # 0000

 

on the phone keypad, after a second you will hear a 

short but steady tone (a “long beep”) from the earpiece, this means that the 
Mini-PABX is now in programming-mode and not user-mode.

If you do not get a steady tone, but instead get 3 short beeps, you have miss-
keyed the entry and need to try again.

Flash Time 

(see below for explanation)

:

If you understand “Flash” Time, then for Australia it's 100 m/Seconds, and to 
make sure it is set correctly, immediately after going into program-mode:
(

*# 0000

) enter 

002#

  

and wait for the tone, then replace the receiver.

After setting the flash-time, the Mini-PABX is set correctly for Australia's 
standard Flash-Time, and you should never have to repeat this setting.

What's Flash-Time?

In plain non-technical language, Flash-Time is the time allowed before the 
telephone provider exchange decides that you have hung-up the call. That is, if 
you put the handset back into the cradle, the telephone exchange knows that the 
call has ended, and the call will be terminated.

However, with a Mini-PABX you will often want to place the handset in the 
cradle and leave the call connected (with Music-on-Hold) to you, or connected 
to another extension, or even for a conference with two extensions and the 
caller.

Therefore, the “Flash Time” is the delay-time before the line is cut. During this 
time, the Mini-PABX can perform certain duties, mainly put the call “on-hold” 
(with “Musical Bells”).

Summary of Contents for 308











Reviews: