Cando 10-0709 Instruction Manual Download Page 14

13 

Cadence number jumps high or low

 

1.

 

Separate bikes that may be paired to the same console code and are cross-talking, or simply run 
transmitter pair stage again on the bike.   

2.

 

Relocate the bike to a different part of the room, away from any RF interference areas. 

 

CAUTION 

EXTERNAL INTERFERENCE MAY BE CAUSED BY OTHER ELECTRONIC DEVICES SUCH AS:   
NEARBY TELEVISIONS, STEREO EQUIPMENT, SPEAKERS, ELECTRICAL WIRE CABLING, ETC. IF YOU 
EXPERIENCE DISTURBANCES IN THE CONSOLE DISPLAY, TRY MOVING YOUR BIKE(S) AWAY FROM 
POTENTIAL RF INTERFERENCE AREAS

 

 

PLEASE NOTE: 

1.

 

The console is designed as a sealed unit and is not meant to be opened other than for the sole purpose 
of installing batteries. Opening the unit will void the warranty. 

2.

 

To clean the console, lightly spray the monitor with an authorized cleaning / disinfectant solution and 
wipe dry with a soft towel. Use of any caustic cleaning solutions will void the warranty. 

3.

 

The console is NOT waterproof; only water resistant. Any excessive exposure to water will void the 
warranty. 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
                  CanDo is a trademark of Goldberg. © 2021 FEI, all rights reserved.                                     rev1121 

Summary of Contents for 10-0709















Reviews: