background image

28

Salt

Water

 

CAUTION

Liquid brine will irritate eyes, skin, and open wounds. 

Gently wash the exposed area with fresh water. Keep 

children away from your water softener.

ADDING SALT TO THE BRINE TANK / CABINET

Use only clean salt labeled for water softener use, such as crystal, pellet, nugget, or button. The use of natural rock salt is discouraged because it 
contains insoluble silt and sand which buildup in the brine tank and cause problems with the system’s operation.

— 

Put 40 kg [80 to 100 lbs] of water softener salt into the brine tank. 

— 

Add the salt directly to the tank, filling it no higher than the top of the brine well. Do NOT overfill the salt tank as the additional weight of salt    

  adds to the potential for salt bridging due to compaction. 

— 

Check the salt level regularly. Remove the lid from the cabinet or brine tank. Ensure that the salt level is above the brine water level.

 

NOTICE

Incorrect start-up, water above the salt level – not enough salt in tank 

– will affect the unit’s capacity and result in hardness slippage. Should 

either of these situations happen, or the unit fails to regenerate for any 

other reason, correct the problem first, then regenerate the unit manually. 

Regenerate two times in a row to restore the reserve capacity and bring the 

media bed back up to specification.

NOTE

The salt level should always be  

above the water level.

SALT BRIDGING

Humidity or poor-quality salt may create a cavity between the water and the salt. This action, known as 

‘bridging’, prevents the brine solution from being made, and prevents your water from being conditioned.
If you suspect salt bridging because of a lack of soft water or salt is NOT being consumed, use a rubber 

mallet to pound on the outside of the plastic brine tank or pour some warm water around the inside edges 

of the salt tank to break up the bridging. Allow four (4) hours to produce a brine solution, then manually 

regenerate the softener. This should always be followed by allowing the unit to use up any remaining salt 

and then thoroughly cleaning out the brine tank.

CLEANING OF YOUR BRINE OR SALT TANK

Salt tanks will build up sludge (undissolved salt) in the bottom that increases over 

time. Every  2 – 3 years the salt tank(s) should be cleaned out and restarted using 

the original start-up  instructions.

SYSTEM MAINTENANCE 

(CONTINUED)

Summary of Contents for 85UF





































Reviews: