Camtec ESB303 Quick Start Manual Download Page 3

 

(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

        

        

          

The figures 1-1A, 1-1B and 1-1C show all 
possible installation variations where 
the ESB303 can be used. The neutral 
must be connected to the unit. If the 
neutral is not connected the ESB303 
remains in the limiting mode. If so, the 
device will overheat, and the internal 
temperature protection will irreversible 
blow. The device is powered between 
phase conductor and the neutral. Each 
phase connection is limited separately 
thus a loss or a breakdown of each line is 
protected by the ESB303 unit. 
The figure 1-1 shows the distribution of 
the potentials in relation to the neutral 
connection. In three-phase systems, the 
effective value of the sinusoidal AC 
mains voltage between an outer 
conductor and the neutral conductor is 
230V, and between two outer 
conductors is approx. 400V.  
The ESB303 cannot be used in 3-phase 
systems without an N-wire. For such 
application we recommend the use of 
our ESB00163 and ESB00323 inrush 
limiters.

 

Fig.1-1A, 3x parallel 1PH 230Vac 16A network 

Fig.1-1B, 3PH 400Vac 16A network, N (neutral) = 16Amax 

Fig.1-1C, 3PH 400Vac 16A network 

Fig.1-1 

Verkoopadres:

 Advantec Electronics

, Industrieweg 10 G, 4731 SC Oudenbosch, Nederland, Tel: (31) 085 87 688 37  

Website: www.advantecelectronics.nl, Email: [email protected] 

Summary of Contents for ESB303







Reviews: