Camsoy Smart Life Camera S1 User Manual Download Page 12

Check whether memory card inserted correctly, please format memory card before using.
2. Why nothing happened after long pressing Confirmation button?
Check battery of camera, please full charge camera for first time using.
3. No reaction of both indicator and camera after press confirmation button.
Try format micro-SD card or use pin to reset camera.
4. Why temperature of camera is high while working?
Camera turns hot especially when IR led turn on, it’s safe to use.
5. How long it takes for battery full charged?
It takes around 2 ~3 hours for full charging the battery. Please use qualified charger, input voltage
5V=1A

11.Attentions

1.Use qualified charger, input voltage 5V/1A.
2. Do not drop this product or subject it to strong impact.
3. Do not touch the camera lens and image sensor directly. If you need to clean, please use dry The
net soft fabric slightly moistened with alcohol and wiped gently to remove dirt;
4. Avoid direct light, such as strong sunlight, focusing lighting otherwise it is easy to cause images
too bright or pulling light (in this case not equipment failure), and reduce the life of the
photosensitive sensor;
5. Avoid working under extreme conditions such as moisture, dust, extreme cold, extreme heat,
etc. Degree -5 °C -50 °C, do not place strong electromagnetic radiation and other places.
6. Avoid heat accumulation, please do not artificially block the ventilation near the camera, keep a
good cooling ring territory.
7. Please strictly abide by the relevant laws and decrees of the state, and shall not use this product
for any illegal purposes, otherwise the consequences will be conceited.

12. Warm Prompt

Please format the TF card before using and format the TF card once every three months.

Force majeure (earthquake, tsunami, lightning, voltage instability) due to natural disasters and
poor use the product hardware, program damage, or data loss, the company does not assume any
responsibility.

The interface between Android and ios is basically the same as that of operation, because

there is a slight difference in the version, there is no detailed introduction here.

Thank you for using CookyCam smart life cameras, we are very sorry for the inconvenience

due to software upgrades or other reasons! If you encounter any problems in use, please contact us
in time. We will be dedicated to serve you 24 hours! You can also pay attention to our official
WeChat or Email, frequency tutorials, product information, and online customer service.

Summary of Contents for Smart Life Camera S1













Reviews: