manualshive.com logo in svg

CAMSO 24D17C, Operation And Maintenance Manual, Page: 24 / 48

Share
Download
CAMSO 24D17C Operation And Maintenance Manual Download Page 24

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso |  12-17 | 24

5.7 After-season long term storage

1. The tracks should be stored indoors, in dry environment with a temperature between 

5° and 25° C. No petrochemicals and related vapors, no electrical devices producing 

ozone should be placed in the same area.

2. The tracks should not be exposed to direct sunlight or heat.

3. Do not lay the rubber components on dirty surfaces contaminated by oil, grease or 

other chemical products

4. Do not paint rubber components.

5. Discharge the tensioning circuit referring to instructions of “Tensioning circuit 

discharge” paragraph in “Routine maintenance instructions” section and leave the 

track in “relaxed” position.

6. Should it be necessary to disassemble the tracks from the undercarriage, lay them on 

the ground on one edge avoiding bending radius less than 30 in (0.75 m).

5.8 Installation after long term storage

1. Check the oil level in the wheel and roller axle hubs following the instructions of “Axle 

oil level check” paragraph in “Routine maintenance” section.

2. Tension the rubber track referring to instruction of “Track tension adjustment” 

paragraph in “Routine maintenance” section

3. Assemble the CTS on the tractor as described in the CTS installation manual. 

Additional copies of the CTS installation manual specific for your machine can be 

found at camso.co or from your authorized Camso CTS dealer.

Summary of Contents for 24D17C

















































Reviews:

No comments