manualshive.com logo in svg

CAMSO 24D17C, Operation And Maintenance Manual, Page: 23 / 48

Share
Download
CAMSO 24D17C Operation And Maintenance Manual Download Page 23

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso |  12-17 | 23

3. Inspect and clean out the cavity behind the tension link on 

a regular basis. 

This cavity can be cleaned out using a screwdriver, small 

bar or water jet and can be reached without removing the 

idler wheels. 

The type and moisture content of the soil will determine 

the frequency that this cavity needs to be inspected and 

cleaned but it is recommended that it is inspected and 

cleaned at least weekly when the CTS are in use.

4. If drive sprocket scrapers are installed 

(optional equipment), inspect and adjust

drive sprocket scrapers. Drive sprocket 

scrapers should be adjusted so that there is 

3 mm clearance between the scraper plate 

and the drive sprocket.

5.6 Yearly maintenance or every 400 working hours

1. Disassemble the Camso track system from the tractor, clean it properly and inspect

the components for damage or wear.

2. Check mounting bolts. After 4 mounting cycles of the track system, the replacement 

of the mounting bolts is recommended, while the washers should be replaced at any 

installation.

3. Should the machine work on sandy soils, wear due to abrasion could appear on 

sprocket/drive wheel bars. This wear is normal and typically does not compromise 

machine functionality. 

4. Replace oil in the axle hubs referring to instructions of “Axle oil replacement” 

paragraph in “Scheduled maintenance” section.

5. Replace oil in the main support hub. Refer to instructions of “main support oil 

replacement” paragraph in the “Scheduled maintenance” section.

Summary of Contents for 24D17C

















































Reviews:

No comments