7
When listening to the FM radio, press the ST./ MONO Button (B16) on remote control to switch between stereo mode and mono mode. The
FM stereo icon “ST” will appear on the display if unit is in stereo mode. It is preferable to receive the program in mono when you are
receiving a weak station.
HINTS FOR BEST RECEPTION:
FM - For best FM reception, the FM lead wire antenna located on the back of the unit
should be fully unwrapped and extended.
NOTE: Automatic tuning depends on the signal strength of the broadcasting station, so weak stations may be skipped. You can manually
tune to find the weak stations if a station gets skipped. With strong signals, the tuner may stop before it reaches the actual broadcast
frequency, so you may need to manually tune for the best reception.
PRESET RADIO STATIONS
1. Press the POWER / STANDBY Button (A1,B1) on main unit or remote control to turn on the unit.
2. Tap the SOURCE Button (A1, B11) on main unit or remote control to select FM radio mode.
3. Press and hold tap the Track Down, Track up (A10, A11, B8, B18) button on main unit or remote control until frequency readout on the
display begins to scan and then release the button for auto search and program preset channels. “PROG” appears in display and
flashing. Auto searching and program will stop at P01 after scan finished, “PROG” shows in display steadily.
Note: If the channels stored during the auto search & programmed preset are not ones you want saved, use the method below for the
manually saving radio presets.
4. Tune to the desired radio station either by “manually” or “automatically” tuning method.
5. Tap the PROG. (B3) on remote control, the next available preset memory number and a flashing PROG. (B3) icon will show in the LCD
display. (Note: ”P01” will show in the display if you are programming preset for first time)
6. Tap the PRE. Button (B15, B19) on main unit or remote control to select the preset number you want to assign the station to.
7. Tap the PROG. (B3) Button to confirm the setting.
8. Repeat above steps 4 - 8 to preset up to 30 FM stations.
RECALLING PRESET MEMORY CHANNELS
In radio mode, recall the pre-set channels by pressing the PRE. Button (B15, B19) on remote control repeatedly.
CD PLAYER OPERATION
Note:
1. This CD player will not only play commercial CDs, but also self-compiled CD-R/RW,MP3 discs. Do not attempt to play CD-ROM, CDI,
VCD, DVD or computer CDs.
2. MP3 is a form of compression. It is an acronym which stands for MPEG Audio Layer 3. MP3 is a type of audio code which is processed
by significant compression from the original audio source with very little loss in sound quality.
● This system supports MPEG 1 Layer 3 and VBR files.
● During VBR file playback, time counter in the display may differ from its actual playback time.
● Bitrate which is supported by MP3 is 32 ~ 320 kbps
PLEASE READ THIS IMPORTANT INFORMATION:
CD mechanisms used in devices like this are designed to read all commercial CDs. It will also read self-compiled CD-R/CD-RW,MP3 discs,
but it may take up to 10 seconds for the actual playback to begin. If playback does not start, it is likely due to the quality of the CD-
R/RW ,MP3 disc and/or the compatibility of the CD compilation software. The manufacturer is not responsible for the playback quality of
CD-R/RW ,MP3 discs.
Do not attach a label or seal to either side of the CD-R/RW,MP3 disc. It may cause a malfunction.
PLAYING A CD
1. Press the POWER / STANDBY Button (A1,B1) on main unit or remote control to turn on the unit.
2. Tap the SOURCE Button (A1, B11) on remote control or main unit to select CD mode and then press the Open the disc compartment.
3. Place an audio CD on the center spindle with its label side facing out towards the CD DOOR. Close the disc compartment.
4. Unit starts to read the disc, “---” shows in display and flashing. After few seconds, the total number of tracks show one second and then
total time of the CD will be shown on the LCD DISPLAY.
5. Press the PLAY / PAUSE (A9, B22) Button on main unit or remote control, PLAY indicator shows in display, the CD will start playing
from first track.
6. Press the volume control Adjust the volume . on main unit or remote control to adjust to the desired volume level.
7. To pause playback, press the PLAY / PAUSE (A9, B22) Button on main unit or remote control. The track time will be paused and PAUSE
indicator will show in display. To resume playing, press the CD PLAY / PAUSE (A9, B22) Button again.
8. You can choose to play your favorite track directly by pressing either the Track Down, Track up (A10, A11, B8, B18) . The LCD Display
will indicate the correct track number selected.
9. To locate a particular section within a track, press and hold the Track Down, Track up (A10, A11, B8, B18) until the section is found.
Release the button to continue playing your selection.
10. To stop playing, press the STOP (A8, B25) button.
PROCEDURE TO PLAYBACK MP3 DISC
To play back CD-R/RW,MP3
1 Press the SOURCE Button (A1, B11) on the remote control, and load an MP3 disc.
2 Press the FOLDER (B15, B19) button to select desired playback folder.
3 Select desired file to be played back by pressing the Track Down, Track up (A10, A11, B8, B18) Button.
4 Press the PLAY / PAUSE (A9, B22). Playback will start and file name will be displayed.
Summary of Contents for CR 1173
Page 2: ...2 A ...
Page 3: ...3 A B ...
