background image

Using with Campbell Scientific Dataloggers 

6.  Configuring the TC35T for use with a Datalogger  

Before you install the TC35T, you must configure it and store the settings in its 
non-volatile memory so that when power is applied it works in the correct way 
with the datalogger. 

If your TC35T is supplied in an enclosure with a datalogger and 
other peripherals, it will normally be pre-configured with the correct 
baud rate and with the default settings. Normally no further 
configuration is required, unless you wish to change the error 
correction mode. 

6.1  Setup 

To enable configuration: 

1.

 

Connect the TC35T to a PC. The serial port on the TC35T allows a direct 
connection to a PC ‘AT’ (9-way) style serial port with a cable that has a pin to 
pin connection system. A Campbell Scientific SC12 cable can be used if no 
other cable is available. 

2.

 

Connect the TC35T to a suitable power supply, ensuring that the power control 
line is held high to force the TC35T to remain switched on permanently during 
configuration. 

3.

 

Select a suitable terminal emulation package (e.g. HyperTerminal, included 
with Microsoft Windows 95/98) to communicate with the TC35T in order to 
configure it. Campbell Scientific’s Term or GT programs can also be used, 
with the datalogger type set to NONE. In the first instance set the terminal 
emulation package to communicate at 9600 baud, 8 bits, 1 stop bit, 1 start bit 
and no parity. The terminal type emulation is not important 

4.

 

To check communications with the TC35T type 

AT&F

 and press 

ENTER

. The 

TC35T should respond on the following line with 

OK

. This resets the TC35T to 

the default settings. Please refer to the TC35T manual for full details of the 
commands. The TC35T uses a similar command set to a ‘Hayes-compatible’ 
telephone modem, with the addition of some extra commands for the 
configuration of the GSM module functions. 

5.

 

The default baud rate setting for the TC35T is automatic baud rate detection. 
You need to set this to fixed operation at 9600 baud for use with Campbell 
Scientific dataloggers. To change the setting type 

AT+IPR=9600

. This will 

change the communications speed and write the setting to non-volatile 
memory. If someone has set another fixed baud rate you may have to 
experiment in changing the terminal emulation baud rate until you get the 
TC35T to respond, allowing you change and fix the rate at 9600 baud. Please 
remember that some terminal emulators, such as HyperTerminal require you to 
click on the disconnect button and then reconnect before the changes to 
communications baud rate come into effect. 

If you get the response ‘ERROR’ or ‘4’ after entering the 
above AT commands, please ensure that the terminal 
software is set up to communicate via the COM port to which 
the TC35T is connected, and 

not

 

with any internal modem 

which may be fitted in the computer.  

NOTE 

CAUTION 

Summary of Contents for Siemens TC35T GSM







































Reviews: