Campbell EC155 Product Manual Download Page 5

Page: 5 / 94

Table of Contents

PDF viewers: These page numbers refer to the printed version of this document. Use the

PDF reader bookmarks tab for links to specific sections.

Introduction ................................................................ 1

Precautions ................................................................ 1

Initial Inspection ........................................................ 2

Overview .................................................................... 2

Specifications ............................................................ 5

5.1

Measurements ......................................................................................5

5.2

Output Signals ......................................................................................7

5.3

Physical Description .............................................................................8

5.4

Power Requirements .......................................................................... 10

Installation ............................................................... 10

6.1

Preparation of Vortex Intake .............................................................. 11

6.2

Mounting ............................................................................................ 12

6.3

Plumbing ............................................................................................ 16

6.3.1

Flow ............................................................................................ 16

6.3.2

Pressure ....................................................................................... 16

6.3.3

Filtration ...................................................................................... 17

6.3.4

Plumbing Connections ................................................................ 19

6.3.4.1

Sample Intake ................................................................... 19

6.3.4.2

Pump................................................................................. 20

6.3.4.3

Zero and Span ................................................................... 20

6.4

Wiring and Connections ..................................................................... 20

Settings .................................................................... 24

7.1

Factory Defaults ................................................................................. 24

7.2

Details ................................................................................................ 25

7.2.1

Bandwidth ................................................................................... 25

7.2.2

SDM Address .............................................................................. 25

7.2.3

Unprompted Output .................................................................... 25

7.2.4

Unprompted Output Rate ............................................................ 26

7.2.5

RS-485 Baud Rate ....................................................................... 26

7.2.6

Analog Output ............................................................................. 26

7.2.7

ECMon

Update Rate ................................................................... 26

7.2.8

Sonic Transducer Shadow Correction ......................................... 26

7.2.9

Temperature Sensor .................................................................... 27

7.2.10

Fixed Temperature Value ............................................................ 27

7.2.11

Heater Manual Control ................................................................ 27

7.2.12

EC100 Barometer ........................................................................ 28

7.2.12.1

Pressure Gain .................................................................... 28

7.2.12.2

Pressure Offset ................................................................. 28

Summary of Contents for EC155






























































































Search results

Summary of Contents for EC155

Reviews:

Brands by name

Popular brands

Campbell EC155, Product Manual

Search results

Summary of Contents for EC155

Reviews:

Brands by name

Popular brands