background image

Solar Radiation Sensor Mounts 

Compliance 

 

CM225:

 

View EU Declaration of Conformity at: 

www.campbellsci.com/cm225-solar-mount

 

6.  Installation 

6.1  Siting 

The solar radiation sensor is usually installed horizontally, but can also be 

installed at any angle including an inverted position. In all cases, it will 

measure the flux that is incident on the surface that is parallel to the sensor 

surface. Site the sensor to allow easy access for maintenance while ideally 

avoiding any obstructions or reflections above the plane of the sensing element. 

It is important to mount the sensor such that a shadow or a reflection will not 

be cast on it at any time. FIGURE 

6-1

 shows how to calculate the distance 

needed from any potential obstruction, using the CMP3 as an example.  

 

FIGURE 6-1.  Solar sensor placement 

If this is not possible, try to choose a site where any obstruction over the 

azimuth range between earliest sunrise and latest sunset has an elevation not 

exceeding 5°. Diffuse solar radiation is less influenced by obstructions near the 

horizon. For instance, an obstruction with an elevation of 5° over the whole 

azimuth range of 360° decreases the downward diffuse solar radiation by only 

0.8%. The sensor should be mounted with the cable pointing towards the 

nearest magnetic pole. For example, in the northern hemisphere, point the cable 

toward the North Pole. 

Summary of Contents for 015ARM
















Reviews: