background image

Spray Gun maintenance

 

pump damage may  

  occur if these 

instructions are not followed.
 

Before  performing  

  any maintenance, 

make sure to relieve pressure from 
system and disconnect power from 
sprayer.

•  Do not use oil based solvents to 

clean equipment after using latex 
based coatings. Use only warm soapy 
water.

•  Always replace clogged gun filters, 

do not attempt to clean them.

•  Carefully follow cleaning and 

storage instructions for your sprayer.

•  Do not use metal or other hard 

objects to pick dried paint material 
from Spray Tip Orifice.

TrIGGEr lOCk

  

pulling the trigger 
must not open the 
gun valve when 
trigger lock is activated.

You should be able to get the actuator 
(#12, page 19) to wiggle slightly with 
your finger while holding the trigger 
against the trigger lock when it is in the 
locked position. If you cannot, adjust 
the trigger position by following these 
instructions:
1.  Place trigger in locked orientation 

(tabs horizontal).

2.  With one hand holding trigger 

lightly against lock, use a 1/4 inch 
nut driver to turn nut (#13, page 19) 
in until trigger starts to come off the 
lock.

3.  Reverse the nut (counterclockwise) 

1/2 turn.

15

Operating Instructions and Assembly Instructions 

Airless Paint Sprayers

TIP SEAl AND wAShEr

Occasionally, you will need to replace 
the silver seal and clear washer located 
inside the tip base.
1.  To replace seal and washer, first 

loosen tip base with adjustable 
wrench, and then remove by hand.

2.  Remove spray tip.
3.  With Phillips screwdriver, push seal 

and washer out from front of tip 
base.

4.  With flat side of seal facing up, place 

seal in base. Make sure it lines up 
properly with base.

5.  Place washer in base. Make sure it 

lines up properly with base.

6.  Put spray tip back in tip base.
7.  Reattach tip base to gun valve.

  

Make sure spray 
tip and tip base fit 
snugly in place. A 
loose fit can lead to misdirected spray 
discharge and a skin injection hazard.

www.chpower.com

15

Summary of Contents for PS240C

























Reviews: