background image

14

Airless Paint Sprayers

Operating Instructions and Assembly Instructions 

www.chpower.com

Storage

ShOrT TErm  

(lESS ThAN ONE wEEk)

wEAr All NECESSAry 

SAFETy GEAr

NECESSAry TOOlS / mATErIAlS:

•  Pump Protector Solution
•  Plastic Wrap
•  3/4 in. or Adjustable Wrench

OIL OR ALKYD BASED PAINT

If sprayer cleaned with mineral spirits, 
simply wrap suction filter housing 
in plastic to keep debris out of 
suction filter. No other preparation is 
necessary.
WATER-BASED PAINT
1.  Prepare Pump Protector solution in 

bucket as directed on container. 

2.  Place suction assembly into 

solution.

3.  Place end of bypass tube into waste 

bucket.

4.  With prime/spray control in PRIME  

position, turn pressure to HIGH 
(completely clockwise).

5.  Turn power switch ON. Circulate 

Pump Protector through bypass 
tube until bucket of solution is 
EMPTY.

6.  Turn pressure to LOW (completely 

counterclockwise).

7.  Wrap suction filter housing in 

plastic to keep debris out of suction 
filter.

lONG TErm  

(mOrE ThAN ONE wEEk)

8.  Remove high pressure hose and 

drain. Reassemble high pressure 
hose to pump.

9.  With spray tip attached to spray 

gun, wrap tip with plastic to 
protect tip.

water based Paint

Pump

Protector

Prepare Pump 

Protector Solution

1

Turn Pressure to LOW  

(completely counterclockwise)

P LASTIC WRAP

Wrap Suction Filter 

Housing in Plastic 

Place Suction 

Assembly in 

Solution

PUmP

PrOTECTION 

SOlUTION

wASTE 

bUCkET

6

Place End of Bypass Tube 

into Waste Bucket

With Prime/Spray 

Control in PRIME 

Position, Turn 

Pressure to HIGH  

(completely clockwise)

14

2

PUmP

PrOTECTION 

SOlUTION

wASTE 

bUCkET

PUmP

PrOTECTION 

SOlUTION

wASTE 

bUCkET

4

Summary of Contents for PS240C

























Reviews: