background image

12

Airless Paint Sprayers

Operating Instructions and Assembly Instructions 

Cleaning Hose and Gun

www.chpower.com

Turn Prime/ Spray 

Control to SPRAY (knob 

is vertical)

If Reversible Tip is 

Used, Rotate Spray Tip 

to CLEAN Position.

While Pulling Trigger, 

Direct Fluid Stream Along 

Inside of Bucket

9

10

CLEANUP FOR CHANGING PAINTS 
OR TEMPORARy STORAGE FOR 
MORE THAN ONE NIGHT 

(Continued)

Allow the 

cleaning fluid

 to continue 

circulating for approximately 10 
minutes.

7.  Turn pressure to HIGH (completely 

clockwise).

8.  Turn prime/spray control to SPRAY/

ROLL position.

9.  If reversible tip is used, rotate spray 

tip to CLEAN position.

10. Point spray gun into bucket of 

paint and pull trigger. 

 

NOTE: 

 To reduce splashing, direct 

fluid stream along inside of bucket 
and above the paint level. 

11. As soon as cleaning fluid is flowing 

from spray gun, release trigger.

 

NOTE:

  It should take less than one 

minute to clear each 25 feet of high 
pressure hose.

12. Engage gun trigger lock.
13. Turn prime/spray control to PRIME 

position.

14. Turn pressure control to HIGH.
15. Lift suction assembly above fluid 

level in bucket.

 

NOTE:

  Allow pump to run until 

empty. 

16. Repeat process (1 - 15) with 

fresh cleaning fluid, to remove 
contaminated cleaning fluid from 
initial cleaning.

Turn Pressure to HIGH 

(completely clockwise).

7

8

Engage Gun Trigger Lock

12

PRIME Position

Lift Suction 

Assembly

HIGH PRESSURE Position 

(completely clockwise)

12

Paint

To Lock

Locked

13

14

15

Summary of Contents for IN425101AV

























Reviews: