Recommended Hookup
Quick
Plug
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Oiler
Regulator
Filter
3
General Safety
Information
(Continued)
●
Always assume the nailer contains
nails. Respect the tool as a working
implement; no horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Do not point the
tool toward yourself or anyone
whether it contains fasteners or not.
Accidental triggering of the nailer
could result in death or serious per-
sonal injury.
●
Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious punc-
ture wound.
●
Do not operate
or allow anyone
else to operate
the nailer if any
warnings or
warning labels
are not legible. Warnings or warning
labels are located on the nailer maga-
zine and body.
●
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution
indicates
a potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
●
Do not make any modifications to the
tool without first obtaining written
Standard B19.3-1991; Safety
Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Operating The Nailer
LUBRICATION
This nailer requires lubrication before
using the nailer for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is
not
required on a daily basis.
The work
surface can
become damaged by excessive lubrication.
Proper lubrication is the owner’s responsi-
bility. Failure to lubricate the nailer prop-
erly will dramatically shorten the life of
the nailer and void your warranty.
1. Disconnect the
air supply from
the nailer to
add lubricant.
2. Turn the nailer
so the air inlet
is facing up.
Place 4-5 drops
of 30 W non-
detergent oil into air inlet. Do not
use detergent oils, oil additives, or
air tool oils. Air tool oils contain sol-
vents which will damage the nailer's
internal components.
3. After adding oil,
run nailer briefly.
Wipe off any
excess oil from
the cap exhaust.
approval from Campbell Hausfeld. Do
not use the nailer if any shields or
guards are removed or altered. Do
not use the nailer as a hammer.
Personal injury or tool
damage may occur.
●
Avoid long extended periods of
work with the nailer. Stop using the
nailer if you feel pain in hands or
arms.
●
Always check
that the Work
Contact Element
(WCE) is operat-
ing properly. A
nail could acci-
dentally be dri-
ven if the WCE
is not working properly. Personal
injury may occur (See "Checking the
Work Contact Element" Section).
●
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice
indicates
important information, that if not fol-
lowed, MAY cause damage to equip-
ment.
●
Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
●
Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
●
Air compressors providing air to the
nailer should follow the require-
ments established by the American
National Standards Institute
Model JB006750
Operating Instructions
OIL
www.chpower.com
O I L
!
WARNING
