background image

11

Limited 5-3-1 Warranty

1.

Duration:

The manufacturer warrants that it will repair, at no charge for parts or labor, the Welder, Welding Gun, or Cables, proven defective in material or

workmanship, during the following time period(s) after date of original retail purchase:

For 5 Years:  The Welder Transformer and Rectifier

For 3 Years:  The Entire Welder (excluding clamps, welding gun, electrode holder, cables, or accessories packed with welder)

For 1 Year:  The Welding Clamps, MIG Gun, Electrode Holder, Accessories, and Welding Cables (as applicable)

2.

Who Gives This Warranty (Warrantor):

The Campbell Group / A Scott Fetzer Company

100 Production Drive

Harrison, OH  45030

Telephone: (513)-367-4811

3.

Who Receives This Warranty (Purchaser):

The original purchaser of the Campbell Hausfeld product.

4.

What is covered under this warranty: 

Defects in material and workmanship which occur within the duration of the warranty period. This warranty

extends to the Welder, the Welders Transformer and Rectifier, Welding Gun or Electrode Holder, and cables only.

5.

What is not covered under this warranty:

A.

Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS

WARRANTY. After this period, all risks of loss, from whatever reason, shall be on the purchaser. Some states do not allow limitations on how long an

implied warranty lasts, so above limitations may not apply to you.

B.

ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT FAILURE OR MALFUNCTION OF

THE CAMPBELL HAUSFELD PRODUCT.  Some states do not allow limitations on how long an implied warranty lasts, so above limitations may not apply

to you.

C.

This warranty does not apply to any accessory items included with the product which are subject to wear from usage; the repair or replacement of

these items shall be at the expense of the owner. These MIG items include but are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt

Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely replacement or maintenance of any of the previously

listed CONSUMABLE parts.

D.

Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s

manual(s) supplied with the product.

E.

Pre-delivery service, i.e. assembly and adjustment.

7. 

Responsibilities of Warrantor under this warranty:

Repair or replace, at Warrantor’s option, products or components which have failed within duration

of the warranty period.

8.

Responsibilities of purchaser under this warranty:

A. Deliver or ship the Campbell Hausfeld product or component to Campbell Hausfeld. Freight costs, if any, must be borne by the purchaser.

B. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9.

When Warrantor will perform repair or replacement under this warranty:

Repair or replacement will be scheduled and serviced according to the

normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.

WG3013

www.chpower.com

Summary of Contents for FARMHAND 125

















Reviews: