background image

 MAINTENANCE 

 REP

AIR

TROUBLESHOOTING

OPERA

TION

ASSEMBL

Y /

 INST

ALLA

TION

SAFETY /

 

SPECIFICA

TIONS

GETTING ST

AR
TED

11

MAINTENANCE AND INSPECTION INSTRUCTIONS

 Disconnect, 

 

  tag and lock out power source, then release all pressure from the system 

 

before attempting to install, service, relocate or perform any maintenance.

 Check compressor often for any visible problems and follow maintenance procedures each time compressor 
is used.

ASME Safety Valve

 

Do not remove or  attempt to adjust the safety valve!

Check the safety valve by performing the following steps: 

1.  Plug the compressor in and run until shut off 

pressure is reached. 

2.  Wearing safety glasses, pull the ring on the safety 

valve to release pressure from compressor tank. 
Use your other hand to deflect fast-moving air 
from being directed toward your face. 

3.  The safety valve should automatically close at 

approximately 40 PSI - 50 PSI. If the safety valve 
does not allow air to be released when you pull 
on the ring, or if it does not close automatically, it 
MUST be replaced. 

 

Safety valve must be replaced if it cannot be actuated or it leaks air after ring is released.

Drain Tank

1.  Turn compressor off and release pressure from system. (To release pressure from system, pull ring on 

ASME safety valve. Deflect escaping air by shielding valve with one hand as you pull ring with other 
hand.) Pull ring until tank is empty.

 

A large amount of fast moving air will be released when the safety valve is opened with 

 

pressure in the tank. Wear ANSI approved Z87.1 safety glasses.

2.  Drain moisture from tank by opening drain valve underneath tank. Tilt tank to remove all moisture.
3.  Clean dust and dirt from tank, air lines and pump cover while compressor is still OFF.

Intake Air Filter Maintenance

Removal, Inspection and Replacement (Figure 6).
The intake filter element should be removed and 
checked periodically. A clogged intake filter can 
decrease compressor performance and cause the 
compressor to overheat.

1. Remove 

bolt.

2.  Remove the filter cover and filter element. Inspect 

each piece.

3.  If the filter element is dirty or clogged, replace it. 
4.  Reinstall filter, cover, and bolt. Thread the intake air filter into the threaded opening in the side of the 

compressor head as illustrated in Figure 6 before use.

IMPORTANT:

 Locate unit as far from spraying area as hose will allow to prevent overspray from clogging 

filter.

 End of Operation/Storage

1.  Turn AUTO/OFF switch to the 

OFF

 position.

2.  Unplug power cord from wall outlet and wrap around handle to prevent damage when not in use.
3.  Wearing safety glasses drain tank of air by pulling the ring on the safety valve. Use other hand to 

deflect fast moving air from being directed toward your face.

4.  Drain tank of condensation by opening drain valve on bottom of tank. Tank pressure should be below 

10 PSI when draining tank.

Figure 5

Figure 6 - Intake Filter Maintenance

Summary of Contents for AC080100





























































Reviews: