background image

MAINTENANCE /

 

REP

AIR

TROUBLESHOOTING

OPERA

TION

ASSEMBL

Y /

 INST

ALLA

TION

SAFETY /

 

SPECIFICA

TIONS

 GETTING 

ST

AR

TED

8

OPERATING INSTRUCTIONS

Before First Start-Up Break-In Procedure

(Complete this procedure before using compressor for the first time. Once completed, it is not necessary to 
repeat.)

1.  Open drain valve located on bottom of tank.
2. Turn 

ON / OFF

 switch to 

OFF

 position.

3.  Plug in power cord.
4. Turn 

ON / OFF

 switch to 

ON

 position and run compressor for 30 minutes.

5. Turn 

ON / OFF

 switch to 

OFF

 position.

6.  Unplug power cord.
7.  Close drain valve.
The compressor is now ready for use.

Operating Procedure

1.  Turn switch to 

OFF

 position and plug in power cord.

2.  Turn regulator knob counterclockwise to close air flow.
3.  Turn switch to 

AUTO

 position.

4.  Compressor will build to maximum pressure and shut off.
5.  With hose attached to outlet of compressor, attach tire chuck or other tool to open end of hose.
6.  Adjust regulator to proper pressure for tool or tire. Operate tool per instructions. 
As air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically 
at its preset “cut-in” pressure. When a tool is being used continuously, the compressor will cycle on and off 
automatically.

7.  Turn switch to 

OFF

 position, unplug power cord and drain tank of air when finished using compressor.

MOISTURE IN COMPRESSED AIR

Moisture in compressed air will form into droplets as it comes from an air compressor pump. When 
humidity is high or when a compressor is in continuous use for an extended period of time, this 
moisture will collect in the tank. When using a paint spray or sandblast gun, this water will be carried 
from the tank through the hose, and out of the gun as droplets mixed with the spray material.

IMPORTANT:

 This condensation will cause water spots in a paint job, especially when spraying other 

than water based paints. If sandblasting, it will cause the sand to cake and clog the gun, rendering it 
ineffective.

A filter in the air line, located as near to the gun as possible, will help eliminate this moisture.

Summary of Contents for AC080100





























































Reviews: