6
DMX
IT
ALIANO
POLSKI
ESP
AÑOL
FRANCAIS
DEUTSCH
ENGLISH
DMX MODE SETTING
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item “DMX Mode”
(coloured background) and confirm with ENTER. A selection box is displayed and you can select the desired DMX mode with the help of the
UP and DOWN controls. Confirm the entry with ENTER and press MENU to return to the main display. The main display is activated automat-
ically after approximately 1 minute of inactivity. The DMX start address is clearly visible in the middle of the display and the DMX mode is
displayed on the bottom line (03Ch, 06Ch, 09Ch, 12Ch 14Ch). If the DMX signal is interrupted, the DMX address symbol will begin to flash. It
will stop flashing once the DMX signal is restored.
001
Operating Mode
Channel mode: 14Ch
System Settings
DMX Address
001
DMX Mode
CH-14
Auto Mode
Auto06
Slave Mode
Off
Advanced Settings
CH-03
CH-06
CH-09
CH-12
CH-14
CONFIGURING AUTO MODE
Each of the 7 available auto programmes consist of a sequence of pre-configured colour change and motion sequences.
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item “Auto Mode”
(coloured background) and confirm with ENTER. Use the UP and DOWN controls to select “Show Mode” and confirm with ENTER. Use UP
and DOWN to select the desired programme (Auto00 to Auto06) and confirm with ENTER. To configure programme run speed, use the UP
and DOWN keys to select the menu item “Show Speed” and confirm with ENTER. Use the UP and DOWN controls to select a value between
01 and 99 (press and hold for quick change of value. 01 = minimum and 99 = maximum speed). Confirm the entry with ENTER and press
MENU to return to the main display. After about 1 minute of inactivity, the main display is automatically activated and the mode is clearly
shown in the centre of the display.
AUTO
Operating Mode
Speed: 099
System Settings
DMX Address
001
DMX Mode
CH-14
Auto Mode
Auto06
Slave Mode
Off
Advanced Settings
Auto Mode
Show Mode Auto00-06
Show Speed
01-99
Sound Mode
Off/On
Sound Sens
00-99
ACTIVATING SOUND CONTROL
Select one of the Auto-programmes as previously described under “CONFIGURING AUTO MODE”. Using the UP and DOWN buttons, select the
menu item “SOUND Mode” (coloured background) and confirm with ENTER, then use UP and DOWN once again to select “On” and confirm
with ENTER. To configure microphone sensitivity, use the UP and DOWN keys to select the menu item “Sound Sens” and confirm with
ENTER. Use the UP and DOWN controls to select a value between 00 and 99 (press and hold for quick change of value. 00 = minimum and
99 = maximum sensitivity). Confirm the entry with ENTER and press MENU to return to the main display. After about 1 minute of inactivity,
the main display is automatically activated and the mode is clearly shown in the centre of the display. The spotlight will now be controlled
via the built-in microphone and will follow the rhythm of the music (bass signals).
SOUND
Operating Mode
Sens: 099
Auto Mode
Show Mode Auto00-06
Show Speed
01-99
Sound Mode
Off/On
Sound Sens
00-99
SLAVE MODE
Press MENU to access the selection menu for system settings. Using the UP and DOWN controls, select the menu item “Slave Mode” (coloured
background) and confirm with ENTER. Press MENU to return to the main display. After about 1 minute of inactivity, the main display is
automatically activated and “SLAVE” is clearly shown in the centre of the display. Connect the slave and the master units (same model) with a
DMX cable and enable one of the standalone modes on the master unit (Auto, Sound). Now the slave unit will follow the master unit.
SLAVE
Operating Mode
System Settings
DMX Address
001
DMX Mode
CH-14
Auto Mode
Auto06
Slave Mode
On
Advanced Settings
