13
ENGLISH
The data and information provided in this manual are to be considered susceptible to change at any time without warning, by CAME cancelli automatici s.p.a.
Activating the remote control
A. insert the existing AF card .
B. Store code in the motherboard.
- The AF board should AL WAYS be in sert ed when the
pow er is off be cause the motherboard only rec og nis es it
when it is pow ered.
Memorisation
- Keep the CH1 key pressed on the base card (the signal LED will fl ash), and with a
key on the transmitter the code is sent, the LED will remain lit to signal the successful
saving of the code.
- Perform the same procedure with the "CH2" key, associating it with another transmitter
key.
CH1 = Channel for direct control of one function performed by the control unit on the gear
motor ("open only" / "open-close-reverse" or "open-stop-close-stop", depending on the
position of dip switches 2 and 3).
CH2 = Channel for direct control of an accessory connected across B1-B2.
N.B. If you wish to change the code on your transmitters in the future, simply repeat the
procedure described above.
Adjustment trimmers
Trimmer FINE ADJ/AMP SENS= Fine
adjustment of amperometric sensitivity
during motor operation: min/max;
Trimmer AMP SENS = Adjustment of
amperometric sensitivity during operating:
min/max;
Trimmer SLOWDOWN/AMP SENS =
Adjustment of amperometric sensitivity
during slowdown: min/max;
Trimmer OP TIME = Adjusting of the stop
zone (open/closed position);
Trimmer ACT = Adjustment of automatic
closing time: 2" to 120";
Trimmer DELAY 2M = Delay on closing
cycle motor 2: 1" to 15";
'(/$<0
ŔŔ
$&7
ŔŔ
237,0(
),1($'-
$036(16
PD[PLQ
$036(16
PD[PLQ
6/2:'2:1
$036(16
PD[PLQ
Caution! Shut off the mains power and disconnect the batteries before servicing the inside of the unit.
e
f
e
f
13
ENGLISH
The data and information provided in this manual are to be considered susceptible to change at any time without warning, by CAME cancelli automatici s.p.a.
Activating the remote control
A. insert the existing AF card .
B. Store code in the motherboard.
- The AF board should AL WAYS be in sert ed when the
pow er is off be cause the motherboard only rec og nis es it
when it is pow ered.
Memorisation
- Keep the CH1 key pressed on the base card (the signal LED will fl ash), and with a
key on the transmitter the code is sent, the LED will remain lit to signal the successful
saving of the code.
- Perform the same procedure with the "CH2" key, associating it with another transmitter
key.
CH1 = Channel for direct control of one function performed by the control unit on the gear
motor ("open only" / "open-close-reverse" or "open-stop-close-stop", depending on the
position of dip switches 2 and 3).
CH2 = Channel for direct control of an accessory connected across B1-B2.
N.B. If you wish to change the code on your transmitters in the future, simply repeat the
procedure described above.
Adjustment trimmers
Trimmer FINE ADJ/AMP SENS= Fine
adjustment of amperometric sensitivity
during motor operation: min/max;
Trimmer AMP SENS = Adjustment of
amperometric sensitivity during operating:
min/max;
Trimmer SLOWDOWN/AMP SENS =
Adjustment of amperometric sensitivity
during slowdown: min/max;
Trimmer OP TIME = Adjusting of the stop
zone (open/closed position);
Trimmer ACT = Adjustment of automatic
closing time: 2" to 120";
Trimmer DELAY 2M = Delay on closing
cycle motor 2: 1" to 15";
'(/$<0
ŔŔ
$&7
ŔŔ
237,0(
),1($'-
$036(16
PD[PLQ
$036(16
PD[PLQ
6/2:'2:1
$036(16
PD[PLQ
Caution! Shut off the mains power and disconnect the batteries before servicing the inside of the unit.
e
f
e
f
