Pa
g.
2
- M
anu
al c
od
e:
3
1
9
U
1
6
319
U
16
ve
r.
0
.
0.
5
0
9
/2
0
0
7 © C
A
M
E c
an
celli auto
mati
ci
s.p
.a. - T
h
e d
ata an
d i
nf
or
m
ati
on r
ep
orte
d i
n thi
s i
n
stall
ati
on
manu
al ar
e s
u
sc
ep
tib
le to
c
h
ang
e at an
y time an
d with
ou
t o
b
lig
ati
on
o
n C
A
M
E c
an
celli auto
mati
ci
s.p
.a. to n
otify u
se
rs.
ENGLISH
Make sure you respect the distances and cable diameters as shown in “cable types and minimal thicknesses” table.
The overall power of the motors must not exceed 480W.
4 Description
2.1 - INTENDED USE
1 Legend of symbols
This symbol indicates sections to be read with particular care.
This symbol indicates sections concerning safety
This symbol indicates notes to communicate to users.
2 Intended use and application
The ZL90 control panel is designed to control the FROGJ and A1824 swing gate operators
The use of this product for purposes other than as described above and installation executed in a manner other than
as instructed in this technical manual are prohibited.
3 Reference Standards
“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”
2.2 - APPLICATION
For its quality processes management Came Cancelli Automatici is ISO 9001:2000 certified, and for its environmental
management it is ISO 14001 certified. Came designs and manufactures entirely in Italy.
This product complies with the following standards:
see chapter 13 - Conformity declaration - pag. 17
.
F U S E S
protection fuse type
Motor/s 6.3 A-F
Electronic board (power supply line) 1.6 A-F
Accessories 1.6 A-F
Control devices 1 A-F
T E C H N I C A L F E AT U R E S
Power supply 230V - 50/60Hz
max. rated power 480 W
Power draw when idling 90 mA
Max power of 24V accessories 37 W
Insulation rating II
Material ABS
Protection rating IP54
operating temperature -20 / +55°C
This product is engineered and manufactured by CAME cancelli
automatici s.p.a. and complies with current safety regulations.
Guaranteed 24 months if not tampered with.
The control panel works on 230V a.c. of power, through the
terminals L-N, 50/60Hz frequency.
Both command and control devices and accessories are 24V
powered. Warning! Accessories must not exceed 37 W overall.
The control unit is fi tted with an amperometric device which con-
stantly regulates the motor’s drive coeffi cient.
When the gate runs into an obstacle, the amperometric sensor
immediately detects an overcharge in the drive and redirects the
gate’s direction of movement, and:
- opens it if it is closing
(1)
;
- closes it if it is opening.
(1)
Warning!: in this case, after 3 consecutive obstacle detections, the gate
will stop open excluding the automatic closing function; for movement
to start again press the command button or use the remote control.
All connections are protected by quick fuses, see table.
The card provides and controls the following functions:
- automatic closing after an open-command;
- pre-fl ashing by the motion indicator;
- obstacle detection when gate is still in any position;
- continual monitoring of photocell operation.
The following command modes are possible:
- open/close;
- open/close and maintained action;
- partially open;
- complete stop.
After detecting an obstacle and depending on the type of con-
nection used, the photocells may cause:
- reopening of the gate when it is closing;
- partial stop or obstacle stand-by.
Apposite trimmers regulate:
- the automatic closing run time;
- the second gate leaf’s motion time difference;
- the amperometric device’s detection sensitivity, in sepa-
rately in terms of normal opening and closing and braking;
- the operation and deceleration speed separately.
Further implemented options:
- connecting up an electric lock (alternatively to the “Open
Gate” indicator light) and possibly adding the “Ram Blow”
function.
