3
Section III - Start Up
1� Remove all external packing materials, tape and protective coverings and inspect for damage� Keep packing materials if damage is discovered�
2� Wipe all surfaces of the cabinet and self-leveling dispensers with a clean damp cloth and dry thoroughly�
3� Select a location within reach of a 208-240 VAC, 50/60 Hz grounded NEMA No� 6-15 electrical outlet�
4� Place the unit near enough to the electrical outlet so that the power cord is not stretched or strained when plugged in�
5� When unit is properly located, engage the two rear caster brakes by pushing down on the wheel brake levers�
6) Make sure the power switch is OFF before plugging into the electrical receptacle, plug the unit in�
7) Carefully place the plates into the self-leveling dispensers, avoid dropping the plates into the silo or allowing the dispenser to bounce excessively�
8) Close both lids and turn the power switch to the ON position for which silo is being used�
Set Point Setup:
• Press the Set key once and Set will be displayed�
• Press the Set key again and set point value will be shown, blinking�
• Use the Up and Down arrows to adjust the set point� (Minimum 80˚F / 26,7˚C, Maximum 175˚F / 79,4˚C)
• Press the Set key to save the new set point�
• Press Set and Down arrow keys at the same time to exit�
Led Indicators:
((•)) Indicates an Error or Alarm�
Display Messages
In normal operation the probe temperature will be displayed� The display blinks when waiting for a parameter to be saved or when there is an error saving a parameter to memory�
The following messages can also appear (Call service for assistance to address the messages displayed):
ERP1
Probe Error (check wiring or replace probe)
Eri
Internal Parameter Error (factory default programming)
ALH
High Temperature Alarm
ALL
Low Temperature Alarm
ooo
Open Probe Error
---
Short Circuited Probe Error
Section IV - Maintenance
The following procedures should be followed during the regular maintenance and cleaning of all Camtherm Plate Heaters:
(READ ALL Warnings below before proceeding)
WARNING:
Make sure unit is off and unplugged from the electrical outlet, plates are removed, and unit is completely cool before cleaning
or maintenance is performed�
WARNING:
Remove the plug by grasping the plug body and pulling it straight out of the receptacle, never pull on the cord�
NOTICE:
Do not use abrasives, harsh chemicals, or chlorine products for cleaning�
WARNING:
Do not steam or pressure clean or hose down the cabinet; this could damage the equipment and possibly cause an electrical
shock to the operator�
WARNING:
Repairs should be done by qualified service personnel only�
A. Cabinet, Exterior
Clean the outside of the cabinet with a mild, non-abrasive soap or detergent in a warm water solution� A commercial
stainless steel cleaner can also be used for this procedure� Allow to air-dry before use�
B. Interior
Clean inside uprights, leveling shelves and baskets with a mild, non-abrasive soap or detergent in a warm water solution� Squeeze out any excess liquid from soft cloth to ensure
liquid does not slosh into the bottom of the unit� A commercial stainless steel cleaner can also be used� Air-dry the unit completely before use�
1
2
C. Casters
Caster maintenance should be performed after every cleaning�
1� Grease swivel raceway of caster using a lubricant such as Lubriplate #930-AA,
Keystone #84EPXLT multi-purpose grease or equivalent� Apply grease using a grease
gun with a needle nose adapter or a tube-type applicator such as Sta-lube Moly-
graph Assembly Lube� These can be obtained at most auto parts stores�
2� Use a light oil such as WD-40 on the hub� Check caster for damage and test caster
spin and swivel rotation before returning to service�
D. Cord and Plug
1� Inspect plug blades for distortion and replace cord if any blades are missing, bent or broken�
2� Inspect exterior wiring� If wires are showing on the outside of the unit remove the unit from service� For service, call Cambro at 800-833-3003 ext� 4118�
