manualshive.com logo in svg

Cambium Networks XIRRUS XA4-240, Installation Manual, Page: 7 / 11

Share
Download
Cambium Networks XIRRUS XA4-240 Installation Manual Download Page 7

XA4-240 Installation Guide

3

Install Mounting Hardware

3A—Ceiling or Wall Mount with Mounting Plate

The following steps use a mounting plate, which offers a secure mount and ease of dismount. 

For a wall mount, 

the locking lever should point down.

 

3B—Pole Mount

For pole mounting, Cambium Xirrus recommends using metal straps (not included with the AP). The metal straps 
can be obtained from BAND-IT-IDEX, Inc. (

www.BAND-IT-IDEX.com

). See their web site for additional contact 

information. Complete the following steps to mount the AP to a pole. 

.

3A—Ceiling or Wall Mount with Mounting Plate

 

3B—Pole Mount

1.

Use the AP mounting plate to mark the 
placement on the ceiling of the cable feed 
opening and of the 4 mounting slots. 

2.

Drill and prepare holes for user-supplied 
screws as appropriate.

3.

Cut an access hole for the cable(s) in the wall 
and draw enough cable through to attach to 
the AP when it is installed.

4.

Align the mounting plate over the prepared 
holes (position the edges with the mounting 
slots flush against the wall.). Feed the cable(s) 
through. Secure the plate with the screws. 

Install the metal bands through the holes in the mounting plate.

Note that the photos below show a different mounting plate. The 
steps for installation are identical, however.

Install the mounting plate 

with the locking lever pointing down

. 

Hand tighten the Band-It strap through the pole mounting plate, 
thread it through the strap buckle and then bend the strap back.

3

Mounting slots

AP attachment 

keyhole slots

Mounting slots

Cable 
feed

Summary of Contents for XIRRUS XA4-240












Reviews:

No comments