manualshive.com logo in svg

Cambium Networks PMP 400 Series, Configuration And User'S Manual, Page: 62 / 98

Share
Download
Cambium Networks PMP 400 Series Configuration And User'S Manual Download Page 62

PMP 400/430 and PTP 200/230 Series Configuration and User Guide

 

pmp-0042 (March 2014)

 

 

Page 61 of 98

 

An SM/BHS has both a configurable 

Region/Country

 

Code

 and, once it registers to an AP or BHM, an 

active 

Regional

 

Code

. After an SM/BHS registers to an AP/BHM, it uses the region code of the AP/BHM to 

determine its DFS behavior and displays the AP/BHM’s region code on its Home => General Status page. 
 
The AP or BHM always operates under its manually configured Region Code (the one on the Configuration 
=> General page), and so does not show a Region Code on its Home => General Status page. 
 
Under normal operations, APs and BHMs operating with DFS (see 

Table 18

) will experience an additional 

minute after power-up or reboot before they will register any SMs or BHSs. SMs and BHSs operating with 
DFS (see 

Table 18

) will experience an additional minute after they reboot before they will register to an AP 

or BHM. 
 
It takes two reboots to set the parameters described below on a module starting from factory defaults. Set 
the 

Region

 

Code/Country Code

 as described above, 

Save Changes

, and 

Reboot

. If the module then 

invokes DFS (based on the region code and frequency band as shown in 

Table 18

), the 

Radio Frequency 

Carriers 

and

 External Antenna Gain

 parameters will be displayed. Set them as described below, 

Save

 

Changes

, and 

Reboot

 again. 

 

 

IMPORTANT!

 

Set the 

Region

 

Code/Country Code

, 

Save

 

Changes

, and 

Reboot

 to see the 

context-sensitive DFS parameters. Unlike with many context-sensitive 
parameters, these do not appear in the GUI with only a 

Save

 

Changes

.

 

 

Setting Radio Frequencies 

APs and BHMs running DFS include an option for setting up to two alternate frequencies on the 
“Configuration => Radio” page, in addition to the primary frequency. These alternate frequencies are used in 
the unlikely event radar is detected and the main frequency is locked out due to DFS detection. If these are 
left at “None”, no backup frequencies will be used in the case of DFS detection, and the AP or BHM will lock 
itself out from any transmission for 30 minutes. 
 
If radar is detected on the main frequency, either at startup or during operation, a Channel Availability Check 
will be performed on the 1

st

 alternate frequency before it is then used for transmission. If radar is detected on 

the 1

st

 alternate frequency, either during Channel Availability Check or during operation, a Channel 

Availability Check will be performed on the 2nd alternate frequency before it is then used for transmission. If 
radar is detected on the 2nd alternate frequency, either during Channel Availability Check or during 
operation, the radio will cease transmission unless or until the primary channel clears its 30-minute lock-out. 
 
The alternate frequencies configured in the AP/BHM must be included in the SM/BHS’s Frequency Scan 
List, or the SMs/BHS can’t follow their AP/BHM if it switches to a new channel. Additional frequencies may 
checked in the Frequency Scan List depending on local practices, for example an operator may want to 
configure an SM to only register on certain frequencies to drive a known SM to AP mapping. Another 
example would be an operator who configures an SM to register on many frequencies so that it may find 
another AP to register to if its usual AP isn’t available. 
 
Note: use site surveys and RF planning to choose alternate frequencies useful for each sector, and consider 
testing on the alternate frequencies to ensure compatibility with the sector’s RF environment. 
 

 

 

Summary of Contents for PMP 400 Series



































































































Reviews:

No comments