Cambium Networks cnPilot R200 User Manual Download Page 30 | Manualshive

Page: 30 / 151

background image

Chapter 3: Advanced Configuration

Two-Level Management

Page

28

Two-Level Management

This section explains how to setup a password for an administrator or user and how to adjust
basic and advanced settings.
cnPilot Home Router supports two-level management: administrator and user. For administrator
mode operation, please type “admin/admin” on Username/Password and click Login button to
begin configuration. For user mode operation, please type “user/user” on Username/Password
and click Login button to begin configuration.

Note
It is highly recommended to change the admin/user passwords to non-default values.

«
...
28
29
30
31
32
...
»

Summary of Contents for cnPilot R200
























































































































































Reviews:

No comments

Related manuals for cnPilot R200

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

Brand: National Instruments Pages: 8

Brand: Lanner Pages: 59

Hotwire 8775 MSDSL

Brand: Paradyne Pages: 10

Monochrome Image Acquisition Device NI 1410

Brand: National Instruments Pages: 34

Brand: AMG Pages: 4

Hotwire 5620 RTU

Brand: Paradyne Pages: 20

Brand: Suttle Pages: 12

Brand: Tripp Lite Pages: 2

Brand: Vivotek Pages: 12

Brand: Johnson Controls Pages: 72

Brand: Siemens Pages: 24

Brand: Siemens Pages: 128

Brand: Siemens Pages: 144

Brand: East Coast Datacom Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands