background image

FibreQuik - Fibre Channel Adapter User Guide 

Login after LIP (yes) 
Full duplex in loop mode (no) 

Attributes used to limit data rate or resources used 

Execution throttle (256 simultaneous I/O) 
IOCB allocation (256) 
DMA window size (PCI only, 64MB) 
Max frame size (1024) or 512, 2048. 
Fibre channel rate in GHz for PC2000 (auto) 
SCSI device types to exclude (none) 
Topology list (P2P_LOOP) 

Error recovery 

Delay after bus reset or other error (10 seconds) 
Maximum command timeout (300) in seconds 
Disconnect time before logging an error (60 sec) 

 

Generate Error Report

 

Accesses the AIX error logging facility. 
 

Trace Cambex FC Adapters

 

Runs the AIX trace facility, looking only for the entries specific 
to the adapter driver. The trace facility must be installed from 
fileset 

bos.sysmgt.trace

 

 

 

 

Change / Show Device Status 

Shows status of alternate paths to the device and allows manual 
unfail of paths.  (Available with Dynamic Path Failover driver 
only). 
 
 

Configure Path / Show Path Status 

Shows path status and allows unconfigured paths to be added.  
(Available with Dynamic Path Failover driver only). 
 

AIX Troubleshooting 

Use the 

errpt

 command to identify the cause of failure.  The 

lsdev

 command will provide the location of the component.  For 

 

- 7 - 

  

Summary of Contents for AIX


















Reviews: