![background image](http://html1.mh-extra.com/html/calrec/type-r/type-r_installation-manual_3515809021.webp)
Assist may be accessed via the front-facing
Setup
port by navigating to
172.16.255.25
in Google Chrome, however the Setup
port may not be connected to a local area network (LAN) and in a studio install scenario may not therefore be readily accessible to
an operator or engineer’s PC. It is therefore recommended that the PC accessing Assist is now connected to the network switch
that serves the surface panels instead. By default, all user interfaces may be accessed via the rear network interfaces, using either
a “
Management
” or a “
StudioA
” subnet. The “
Management
” subnet resides in the
172.29/16
address space and provides
access to all applications and services running on the core. The “
StudioA
” subnet resides in the
172.17/16
address space
and provides access to the
Assist
,
CoreConfigure
&
CalrecConnect
applications, as well as the console control service.
Note:
Type R is designed to support a Touch Interface if the PC provides this.
To use either subnet configure your PC’s ethernet adaptor as follows:
•
Management-IPaddress172.29.0.1,subnetmask255.255.0.0
•StudioA-IPaddress172.17.0.1,subnetmask255.255.0.0
Note: Default “Studio B” and “Studio C” subnets will be added in a later version
To create a new
Show
follow these steps:
1. Open Google Chrome, type
172.16.255.25
into the address bar and press enter to navigate to the
Assist
landing page.
2. In the menu on the left-hand side, navigate to
Shows&snapshots
then
Shows
in the sub-menu.
3. In the footer menu select
New
, the
CreateaShow
dialogue will be displayed.
Select the
Default_Show
template show and click
Next
.
4. Fill in the form to label and describe your Show, then click
CreateNewShow
.
You will be automatically redirected to the
Faderlayout
screen.
5. From here you may begin to configure your mixer with DSP paths, routing etc.
However we would recommend that you continue to complete the setup before doing this.
Please refer to the Type R Assist Manual or Type R Assist and Console Operation Manual for more guidance.
8. ACCESS ASSIST SETUP AND CREATE A NEW SHOW
9. CONNECT TO ASSIST FROM THE STUDIO OR MANAGEMENT SUBNETS
Application
Setup Port
(front of core)
Management subnet
(back of core)
Studio A subnet
(surface panels)
Assist
172.16.255.25
172.29.1.1
172.17.1.1
Calrec Connect
172.16.255.60
172.29.1.21
172.17.1.21
Software Updater
172.16.255.40
172.29.1.22
172.17.1.22
Configure
172.16.255.19
172.29.1.23
172.17.1.23
To access the
Assist
,
CoreConfigure
&
CalrecConnect
applications
, from the various connection points in the system type the
corresponding IP address shown in the table below into the Google Chrome address bar address bar.
IP ADDRESSES FOR ACCESS TO ASSIST, CONNECT, SOFTWARE UPDATER & CONFIGURE USER INTERFACES
Summary of Contents for TYPE R
