THERMOSTAT
First turn the control dial to any position other than off
0
(except model 6616).
To increase the temperature, turn the thermostat dial to setting 9.
To reduce the temperature, turn the thermostat dial anti-clockwise (to setting 1)
The appliance will stop automatically as soon as it reaches the chosen temperature. It will restart, if necessary,
to maintain this temperature.
FROST-FREE POSITION
This position enables you to keep the temperature automatically above 0°C in a normally insulated room, whose volume corresponds
to the power of your appliance.
To do this:
- set the thermostat dial to frost-free position .
- turn the control dial to (mod. 6618 / 6670) or half-power (mod. 6610 / 6620 / 6672).
OVERHEAT SAFETY CUT-OUT
5 - MAINTENANCE
■
After turning the control dial to
0
, or the thermostat dial
to for model 6616, unplug the appliance and let it cool
down completely.
■
Regularly dust the air inlet and outlet grills with a dry cloth or
vacuum cleaner, without dismantling the appliance.
■
To remove stains, use a slightly dampened cloth.
■
Never use alcohol or solvents.
6 - STORAGE
If the appliance is not to be used for some time, unplug it and
protect it from dust and damp.
Wait for the appliance to cool before storing it.
8 - SOLUTIONS TO POSSIBLE PROBLEMS
ENG
For any other problems, please contact your retailer or your Approved Service Centre.
Problems
Possible causes
Solutions
The appliance does not heat
It is not plugged in correctly.
Check connections.
The control dial is set to "off":
Turn it to , or or .
0
(except 6616).
The thermostat dial setting
Turn it to a higher setting.
is too low compared with
the temperature in the room.
The appliance turned itself
See "overheat safety device"
off automatically, as the air
paragraph.
inlet (or air outlet) is clogged.
The appliance has been
Stand up the appliance
tipped over: the anti-tip-over
and place it on a fully horizontal floor.
safety device has cut the power supply.
The appliance does not bl ow out
The "fan" position has not
Turn the control dial to the
hot air: (mod. 6670/6672)
been selected.
"fan" setting.
for the 6670, for the 6672
If the appliance still does not blow out hot
air, contact an Approved Service Centre.
The appliance does not heat enough:
The thermostat setting is too low.
Increase the thermostat setting.
The power choice is too low.
Turn the control dial to the next highest
setting. (mod. 6610 / 6620 / 6672).
3
Important: Never let water enter the appliance.
If the power lead is damaged, or if the appliance becomes
defective, please consult an Approved Service Centre; a special
tool is needed to dismantle the appliance.
THERMOSTAT
First turn the control dial to any position other than off
0
(except model 6616).
To increase the tempera t u r e, turn the thermostat dial to setting 9.
To reduce the temperature, turn the thermostat dial anti-clock-
wise (to setting 1)
The appliance will stop automatically as soon as it reaches the
chosen temperature. It will restart, if necessary,
to maintain this temperature.
FROST-FREE POSITION
This position enables you to keep the temperature automatical-
ly above 0°C in a normally insulated room, whose volume cor-
responds to the power of your appliance.
To do this:
- set the thermostat dial to frost-free position .
- turn the control dial to (mod. 6618 / 6670) or half-power
(mod. 6610 / 6620 / 6672).
4
5
T H E N F O R A L L M O D E L S P R O C E E D A S F O L L O W S :
- unplug the power plug
- remove dust and clean the grills without disassembling the appliance.
- let the appliance cool down for 15 mins.
- plug in the appliance and turn it back on.
■
If the overheat safety device cuts out again, have the appliance checked by
an approved service centre.
■
If the appliance tips over.
To restart the appliance, put it back into a stable upright position.
In some circumstances, the safety cut-out
device automatically cuts the electrical power
supply.
- In the event of overheating, first do the follo-
wing:
■
Mod. 6616: turn the thermostat dial to frost-
free position .
■
Other models: turn the control dial to
stop:
0
.
OVERHEAT SAFETY CUT-OUT
7 - GUARANTEE
This appliance is intended for domestic or office use only. It is
not suitable for industrial use or for use in public places.
Failure to comply with the terms of these instructions will ren-
der the guarantee null and void.