background image

 

REEL MOWER OPERATOR

’S MANUAL (RL205H/207H) 

Evergreen Turf Equipment

, LLC • 1028 4

th

 St. SW, Bldg. A 

• Auburn, Washington 98001 • caltrimmer.com

 

 

4.  REEL BLADE / BED KNIFE 

 

 

 

Reel blades and bed knife edges are sharp. Wear 
gloves when making any adjustments. Never stand in 
front of the unit or attempt any adjustments while the 
engine is running. Remove the reel drive chain 
before making any 
adjustments. 
If you are unable to 
properly adjust these, 
consult your dealer 
before proceeding. 

 
Reel mowers, unlike rotary mowers, use a scissors 
action to cut grass. The grass is cut as it passes between 
the edges of the reel blade and the bed knife located on 
the bottom of the mower frame.

 

 
This function of the mower is pre-set at the factory, but 
based on the type of grass and other factors, further 
adjustment may be necessary. As the blade reel and bed 
knife wear, additional adjustment will be required. 

 

The clearance between the reel and the bed knife is 
controlled by two adjusters on the topside of the mower. 

 
The adjusters raise and lower each side of the bed knife 
in relation to the reel, increasing or decreasing the 
clearance and should be moved as evenly as possible. 
 

 
Turning the adjuster 

clockwise reduces

 the clearance 

between the bed knife and reel blade, while turning it 

counter-clockwise increases

 the clearance. When 

properly adjusted, there should be slight contact between 
the reel blade and bed knife across the full width.  
 

 

With the unit tipped back slightly and secured in place, 
the blade /bed knife contact can be checked by manually 
rotating the blade forward and use a narrow strip of 
paper to check the cutting action. 

 

 

 

NOTE: Excessive contact will cause overheating and 
damage to the parts. 

Insufficient contact will not allow 

for the grass to be cut. Any excessive noise means that 
the adjustment is too tight. It is not recommended that 
the reel be engaged for extended periods of time when 
not cutting grass as the moisture provides a level of 
lubrication to the cutting surfaces while in use. 

Replacement Parts 

Replacement parts are available from Authorized 
California Trimmer Dealers. Parts manuals, service 
manuals and videos are available at our website: 
http://caltrimmer.com 

IMPORTANT:

 Never use parts or accessories not 

supplied by California Trimmer as they may cause 
diminished performance or unforeseen safety hazards. 
 

 

Summary of Contents for RL205HC











Reviews: