Reset the unit
Power on/off
1.Turn off the unit power.
2.
(
)
- Rotate the volume control to adjust
volume level.
- Press the
button short and repeatedly
to select the
volume, bass, treble,
balance and fader.
- Rotate the volume control to adjust level of
the selected sound mode:
- VOL:00,01 ~ 44,45
- BAS / TRE: -7, -6 ~,0, ~ +6,+7,
- BAL: 7R,6R, ~,0, ~, 6L,7L
- FAD: 7R, 6R, ~, 0, ~, 6F,7F
- Loudness: LOUD ON / OFF
- E
: DSP OFF, POP, ROCK,
CLASSIC, FLAT
1. In each mode, w
Press the
button and hold for more
than 2 seconds to access system setup
menu mode, then
In power off mode, switch on the unit by
pressing any button except the
(
)
button. When the system is on, press and
hold the
on/off button
for about
2 sceconds to turn off the unit.
OPEN
POWER
Sound adjustment
System menu
SEL
Note:
SEL
When operating the unit for the first time,
after replacing the car battery or changing
the connections, you must reset the unit.
the sound setting that you
would like to adjust:
Press the
button (
) to fold down
the front panel and remove it, then press
the
button with a ballpoint pen or
similar object to restart the unit.
OPEN
RESET
qualizer mode
“TA SEEK or TA ALARM”
“PI SOUND or PI
MUTE”
“RETUNE L or RETUNE S”
g
g
g
hen the unit has not been
adjusted for about 2 seconds, the current
setting will be saved and it returns to the
previous mode.
2. When using preset EQ modes, you
cannot have access to Bass and Treble
settings.
press the
button
momentarily to select the menu items in
sequence as follows:
SEL
“MASK DPI or MASK ALL”
“TAVOL 17”
(traffic announcement volume)
“CLOCK
24 or 12” (Clock format)
)
EXIT
After selecting the desired menu item,
r
to select the mode
of the selected item.
g
g
g
“BEEP ON/OFF”
(beep sound on/off
otate the volume control
g
“TA SEEK or TA ALARM”
- TA SEEK mode:
- TA ALARM mode:
Note:
“PI SOUND or PI MUTE”:
(search for traffic
announcement/traffic announcement
alarm)
When a newly tuned station does not
receive traffic information for 5 seconds,
the radio retunes to next station which has a
different PI and which broadcasts traffic
information.
If, during the chosen retune time (30
seconds for a short retune or 90 seconds for
a long retune), the unit can no longer
receive the current station which was
broadcasting traffic information, it will start
to search for the next station that has the
same PI.
If no station with the same PI is found after
one search cycle, the radio will search for
the next station broadcasting traffic
announcements.
Select this mode to switch off the automatic
retune. The radio will bring up a warning
message “NO TP, TA” on the LCD display
and emit a double beep sound (ALARM).
If a newly tuned station does not broadcast
any traffic information for 5 seconds, a beep
can be heard.
If the unit can no longer receive the current
station during the chosen retune time, a
beep sound can also be heard.
If a newly tuned station has no RDS signal,
the message “PI SEEK” disappears.
TP: Traffic Program.
PI: Program Identification.
In some regions, there is a possibility of
having two different stations with the same
frequency but different PI codes.
If “PI SOUND” is selected, radio will switch
to the new station with a different PI for a
few seconds before switching back to the
current station that was broadcast initially.
If “PI MUTE” is selected, the radio will not
broadcast the new station that is received.
General Operations
Summary of Contents for RCD 264
Page 1: ......
