background image

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900  \  fx. 714.535.7902

[email protected]  \  calilighting.com

© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.

Installation Instructions

LLED

8700-OL

12 of 12

lip

LEDs

Maintenance & Warranty

CLEANING MATERIALS

The use of solvents and/or cleaners which are not compatible with polycarbonate will result in the softening, crazing, and/or cracking of the 
plastic part. This is especially true of polycarbonate lamps and mounting bases which may be under stress in their normal applications.

COMPATIBLE WITH POLYCARBONATE:

 

• Mild soap and water 

 

 

• Mineral Spirits   

 

• Isobutyl alcohol

 

• VM and P Naphtha 

 

 

• Varsol No.2 

 

 

• Mexane

 • 

Freone 

TF 

and 

TE-35 

  • 

Ethanol 

   • 

Dirtex 

    

 
 

• 2% Sol. Reg. Joy   

 

 

• 10% Sol Bon Ami  

 

• White Kerosene   

 

 
 

• Methyl alcohol   

 

 

• Heptane 

 

 

• Petroleum Ether/65 degrees C 

 
 

• Isopropyl alcohol   

 

 

• Lacryl PCL-2035 polycarbonate cleaner

  

NOT COMPATIBLE WITH POLYCARBONATE

 • 

Trichlor 

    • 

Gasoline   • 

ll 

Liquid 

Detergents

 

• Acetone  

 

 

 

• Carbon Tetrachloride 

 

• Pink Lux (Phosphate free)

 

• Triclene 

 

 

 

• Chlorinated Hydrocarbons   

•#1 & #3 denatured alcohol

 

• Methyl Ethyl Keytone (MEK)  

 

• Texize-8006, 8129, 8758   

• MIBK   

 

 

 

 
 • 

Liquid 

Cleaner 

– 

8211 

  • 

Toluol 

   • 

Agitene 

   

 
 • 

Benzol 

    • 

Ajax 

   • 

Kleenol 

Plastics 

  

 
 • 

Lysol 

    • 

Stanisol 

Naphtha 

  • 

Oils

 

• Lemon Joy (phosphate free)  

 

• Diversol 

 

 

• Lestoil

WARRANTY

The manufacturer warrants this product to be free for (1) year against any defects that are due to faulty materials or workmanship. This 
warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be 
defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s 
discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or 
mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not in 
accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of accident, 
misuse, abuse, negligence, alteration, or faulty installation or any other failure not relating to faulty workmanship. This warranty shall 
not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The 
manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, or fitness for a particular purpose, 
other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential 
or incidental loss or damage, including any labor/expense costs involved in the replacement or repair of said product. 

Summary of Contents for LipLeds LLED8700-OL













Reviews: